Ubuntu-fr

bourrinlepoulpe

problèmes usb / son ... svp

salut j'ai un problème car j'ai pas de son et mon port usb ne marchent pas.
j'ai un pc relativement récent mais les installations ne marchent pas dessus meme avec des opions comme linux noapic acpi=off. elles foirent toutes (win xp, ubuntu, mandrake, fedora, knoppix et sage 3.1)
donc j'ai installer sur mon disque dur dans un autre pc puis je l'ai remis en place.
la l'install c'est passée nickel mais après avoir reconfiguré X, je sais pas du tout comment faire pour le son et l'usb

merci de bien vouloir m'aider

voici mon dmesg

Linux version 2.6.10-5-k7-smp (buildd@terranova) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 SMP Thu Aug 18 23:35:20 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff8000 (ACPI data)
BIOS-e820: 000000000fff8000 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffee0000 - 00000000fff00000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
found SMP MP-table at 000fbc70
On node 0 totalpages: 65520
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 61424 pages, LIFO batch:14
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 AMI                                   ) @ 0x000fab70
ACPI: RSDT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff0000
ACPI: FADT (v001 AMIINT SiS740XX 0x00000011 MSFT 0x0100000b) @ 0x0fff0030
ACPI: MADT (v001 AMIINT SiS740XX 0x00001000 MSFT 0x0100000b) @ 0x0fff00c0
ACPI: DSDT (v001    SiS      746 0x00000100 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 2000.019 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 251376k/262080k available (1612k kernel code, 10076k reserved, 730k data, 192k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3973.12 BogoMIPS (lpj=1986560)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found!
CPU0: AMD Athlon(tm) XP 2400+ stepping 01
per-CPU timeslice cutoff: 731.38 usecs.
task migration cache decay timeout: 1 msecs.
Total of 1 processors activated (3973.12 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
Brought up 1 CPUs
CPU0:
domain 0: span 01
  groups: 01
  domain 1: span 01
   groups: 01
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4548k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfdb31, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Uncovering SIS963 that hid as a SIS503 (compatible=0)
Enabling SiS 96x SMBus.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
audit: initializing netlink socket (disabled)
audit(1124745653.624:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
PCI0 PS2M PS2K UAR1 USB1 USB2 EHCI  LAN  MDM
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4548KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
    ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IBM-DJNA-370910, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 17803440 sectors (9115 MB) w/1966KiB Cache, CHS=17662/16/63, UDMA(33)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2
Probing IDE interface ide1...
hdc: GENERIC DVD RW 8XMax, ATAPI CD/DVD-ROM drive
hdd: CDRW2224 PLUS, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ext3: No journal on filesystem on hda1
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 24X CD-ROM CD-R/RW drive, 768kB Cache
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
ts: Compaq touchscreen protocol output
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
Real Time Clock Driver v1.12
input: PC Speaker
inserting floppy driver for 2.6.10-5-k7-smp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 746 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 64M @ 0xd0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
i2c-sis96x version 1.0.0
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
ACPI: PCI interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18
intel8x0_measure_ac97_clock: measured 49957 usecs
intel8x0: clocking to 48000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci_hcd 0000:00:03.0: Silicon Integrated Systems [SiS] USB 1.0 Controller
ohci_hcd 0000:00:03.0: irq 20, pci mem 0xcfffd000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ACPI: PCI interrupt 0000:00:03.1[b] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:03.1: Silicon Integrated Systems [SiS] USB 1.0 Controller (#2)
ohci_hcd 0000:00:03.1: irq 21, pci mem 0xcfffe000
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
usb 2-3: new full speed USB device using ohci_hcd and address 2
ACPI: PCI interrupt 0000:00:03.2[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:03.2: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 0000:00:03.2: irq 23, pci mem 0xcffff000
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
PCI: cache line size of 64 is not supported by device 0000:00:03.2
ehci_hcd 0000:00:03.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 6 ports detected
usb 2-3: device descriptor read/all, error -110
sis900.c: v1.08.07 11/02/2003
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xd400, IRQ 19, 00:0b:6a:56:10:e7.
usb 3-6: new high speed USB device using ehci_hcd and address 2
usb 3-6: device descriptor read/64, error -71
usb 3-6: device descriptor read/64, error -71
usb 3-6: new high speed USB device using ehci_hcd and address 3
usb 3-6: device descriptor read/64, error -71
usb 3-6: device descriptor read/64, error -71
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
NET: Registered protocol family 24
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c031ae40(lo)
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
apm: BIOS not found.
eth0: Media Link On 10mbps half-duplex
ip_tables: (C) 2000-2002 Netfilter core team
eth0: no IPv6 routers present
Unable to handle kernel paging request at virtual address 9628c041
printing eip:
c0172ea7
*pde = 00000000
Oops: 0000 [#1]
PREEMPT SMP
Modules linked in: ipt_TCPMSS ipt_tcpmss iptable_filter ip_tables proc_intf freq_table cpufreq_userspace cpufreq_ondemand cpufreq_powersave video sony_acpi pcc_acpi button battery container ac ipv6 af_packet pppoe pppox ppp_generic slhc sis900 ehci_hcd ohci_hcd usbcore snd_intel8x0 snd_ac97_codec snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd soundcore snd_page_alloc i2c_sis96x i2c_core shpchp pci_hotplug sis_agp agpgart analog gameport floppy pcspkr rtc reiserfs md evdev tsdev dm_mod capability commoncap psmouse mousedev parport_pc lp parport ide_cd cdrom ext2 ext3 jbd mbcache ide_generic sis5513 ide_disk ide_core unix thermal processor fan fbcon font bitblit vesafb cfbcopyarea cfbimgblt cfbfillrect
CPU:    0
EIP:    0060:[<c0172ea7>]    Not tainted VLI
EFLAGS: 00010286   (2.6.10-5-k7-smp)
EIP is at iput+0x25/0x7c
eax: 9628c02d   ebx: ca898478   ecx: ca898488   edx: ca898488
esi: cb11a444   edi: cb11a44c   ebp: 00000043   esp: cfeb9ed4
ds: 007b   es: 007b   ss: 0068
Process kswapd0 (pid: 129, threadinfo=cfeb8000 task=cfe8ba80)
Stack: cb1897ac cb11a464 ca898478 c01704e4 ca898478 00000000 00000087 c037ab20
       cfeb8000 cffeea40 c01708f6 00000080 c0145fc5 00000080 000000d0 00000cc6
       00000202 0007d000 00000000 00000080 0000009c 00000000 00000001 c02d6880
Call Trace:
[<c01704e4>] prune_dcache+0x105/0x18d
[<c01708f6>] shrink_dcache_memory+0x1f/0x45
[<c0145fc5>] shrink_slab+0x11f/0x1a0
[<c0147460>] balance_pgdat+0x285/0x309
[<c01475b4>] kswapd+0xd0/0xee
[<c012fabe>] autoremove_wake_function+0x0/0x57
[<c0102e56>] ret_from_fork+0x6/0x14
[<c012fabe>] autoremove_wake_function+0x0/0x57
[<c01474e4>] kswapd+0x0/0xee
[<c0101295>] kernel_thread_helper+0x5/0xb
Code: 04 e9 bf fe ff ff 83 ec 0c 89 5c 24 08 8b 5c 24 10 85 db 74 53 8b 83 98 00 00 00 83 bb 30 01 00 00 20 8b 40 24 74 51 85 c0 74 07 <8b> 48 14 85 c9 75 3e 8d 43 1c c7 44 24 04 24 86 2d c0 89 04 24

Dernière modification par bourrinlepoulpe (Le 22/08/2005, à 20:38)