Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 24/08/2023, à 15:58

xunil2003

Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

bonjour,

Sur mon pc portable j'utilise Ubuntu 16.04.5.
Je voudrais savoir si il est possible d'installer une clé usb wifi 6E ax3000 ?

https://fr.aliexpress.com/item/10050056 … 5737006_27

La clé est reconnu comme ceci avec lsusb :

Bus 002 Device 007: ID 0bda:1a2b Realtek Semiconductor Corp. 

Extrai dmesg :

[    9.418782] r8169 0000:02:00.0 enp2s0: link down
[    9.418830] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
[    9.422656] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[   15.060317] vboxdrv: loading out-of-tree module taints kernel.
[   15.060462] vboxdrv: module verification failed: signature and/or required key missing - tainting kernel
[   15.065923] vboxdrv: Found 8 processor cores
[   15.084359] vboxdrv: TSC mode is Invariant, tentative frequency 2195013043 Hz
[   15.084360] vboxdrv: Successfully loaded version 5.1.38_Ubuntu (interface 0x002a0000)
[   15.092620] VBoxNetFlt: Successfully started.
[   15.100476] VBoxNetAdp: Successfully started.
[   15.108126] VBoxPciLinuxInit
[   15.110119] vboxpci: IOMMU not found (not registered)
[   26.746289] random: crng init done
[   26.746298] random: 7 urandom warning(s) missed due to ratelimiting
[   31.712755] kauditd_printk_skb: 15 callbacks suppressed
[   31.712756] audit: type=1400 audit(1692869221.421:27): apparmor="DENIED" operation="open" profile="/usr/sbin/mysqld-akonadi///usr/sbin/mysqld" name="/proc/1654/status" pid=1654 comm="mysqld" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[   31.712760] audit: type=1400 audit(1692869221.421:28): apparmor="DENIED" operation="open" profile="/usr/sbin/mysqld-akonadi///usr/sbin/mysqld" name="/sys/devices/system/node/" pid=1654 comm="mysqld" requested_mask="r" denied_mask="r" fsuid=1000 ouid=0
[   31.712824] audit: type=1400 audit(1692869221.421:29): apparmor="DENIED" operation="open" profile="/usr/sbin/mysqld-akonadi///usr/sbin/mysqld" name="/proc/1654/status" pid=1654 comm="mysqld" requested_mask="r" denied_mask="r" fsuid=1000 ouid=1000
[   68.156920] iwlwifi 0000:03:00.0: RF_KILL bit toggled to enable radio.
[   68.156928] iwlwifi 0000:03:00.0: reporting RF_KILL (radio enabled)
[   68.170899] iwlwifi 0000:03:00.0: Radio type=0x2-0x2-0x1
[   68.269693] iwlwifi 0000:03:00.0: Radio type=0x2-0x2-0x1
[   68.331218] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[   68.417930] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[   69.360936] wlp3s0: authenticate with 14:0c:76:9f:39:c0
[   69.365030] wlp3s0: send auth to 14:0c:76:9f:39:c0 (try 1/3)
[   69.367890] wlp3s0: authenticated
[   69.372061] wlp3s0: associate with 14:0c:76:9f:39:c0 (try 1/3)
[   69.376025] wlp3s0: RX AssocResp from 14:0c:76:9f:39:c0 (capab=0x1411 status=0 aid=2)
[   69.381605] wlp3s0: associated
[   69.409381] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[10936.085416] perf: interrupt took too long (2536 > 2500), lowering kernel.perf_event_max_sample_rate to 78750
[14760.777215] perf: interrupt took too long (3217 > 3170), lowering kernel.perf_event_max_sample_rate to 62000
[15131.552688] usb 2-1.3: new high-speed USB device number 6 using ehci-pci
[15131.661884] usb 2-1.3: New USB device found, idVendor=0bda, idProduct=1a2b
[15131.661891] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[15131.661895] usb 2-1.3: Product: DISK
[15131.661899] usb 2-1.3: Manufacturer: Realtek
[15131.697136] usb-storage 2-1.3:1.0: USB Mass Storage device detected
[15131.697251] scsi host6: usb-storage 2-1.3:1.0
[15131.697410] usbcore: registered new interface driver usb-storage
[15131.699744] usbcore: registered new interface driver uas
[15132.890442] scsi 6:0:0:0: CD-ROM            RTK      Driver Storage   2.03 PQ: 0 ANSI: 0 CCS
[15132.894217] sr 6:0:0:0: [sr1] scsi3-mmc drive: 0x/0x caddy
[15132.894752] sr 6:0:0:0: Attached scsi CD-ROM sr1
[15132.895338] sr 6:0:0:0: Attached scsi generic sg3 type 5
[15140.373774] UDF-fs: warning (device sr1): udf_load_vrs: No anchor found
[15140.373779] UDF-fs: Scanning with blocksize 512 failed
[15140.385772] UDF-fs: warning (device sr1): udf_load_vrs: No anchor found
[15140.385776] UDF-fs: Scanning with blocksize 1024 failed
[15140.404713] UDF-fs: INFO Mounting volume 'AutoInstall', timestamp 2022/12/08 03:34 (1000)
[15188.418144] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio.
[15188.418151] iwlwifi 0000:03:00.0: reporting RF_KILL (radio disabled)
[15188.418339] wlp3s0: deauthenticating from 14:0c:76:9f:39:c0 by local choice (Reason: 3=DEAUTH_LEAVING)
[15188.420826] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.420832] wlp3s0: HW problem - can not stop rx aggregation for 14:0c:76:9f:39:c0 tid 0
[15188.422542] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422548] wlp3s0: failed to remove key (0, 14:0c:76:9f:39:c0) from hardware (-5)
[15188.422722] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422730] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422738] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422749] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422763] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422842] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.422847] wlp3s0: failed to remove key (1, ff:ff:ff:ff:ff:ff) from hardware (-5)
[15188.423866] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15188.423876] iwlwifi 0000:03:00.0: Not sending command - RF KILL
[15560.323550] iwlwifi 0000:03:00.0: RF_KILL bit toggled to enable radio.
[15560.323557] iwlwifi 0000:03:00.0: reporting RF_KILL (radio enabled)
[15560.341081] iwlwifi 0000:03:00.0: Radio type=0x2-0x2-0x1
[15560.439757] iwlwifi 0000:03:00.0: Radio type=0x2-0x2-0x1
[15560.504437] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[15560.587032] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[15561.554101] wlp3s0: authenticate with 14:0c:76:9f:39:c0
[15561.555194] wlp3s0: send auth to 14:0c:76:9f:39:c0 (try 1/3)
[15561.559341] wlp3s0: authenticated
[15561.562314] wlp3s0: associate with 14:0c:76:9f:39:c0 (try 1/3)
[15561.566042] wlp3s0: RX AssocResp from 14:0c:76:9f:39:c0 (capab=0x1411 status=0 aid=2)
[15561.567805] wlp3s0: associated
[15561.576892] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[15661.138312] usb 2-1.3: USB disconnect, device number 6
[16842.535177] usb 2-1.1: new high-speed USB device number 7 using ehci-pci
[16842.644047] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=1a2b
[16842.644054] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[16842.644058] usb 2-1.1: Product: DISK
[16842.644061] usb 2-1.1: Manufacturer: Realtek
[16842.644746] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[16842.646052] scsi host6: usb-storage 2-1.1:1.0
[16843.856737] scsi 6:0:0:0: CD-ROM            RTK      Driver Storage   2.03 PQ: 0 ANSI: 0 CCS
[16843.861315] sr 6:0:0:0: [sr1] scsi3-mmc drive: 0x/0x caddy
[16843.861771] sr 6:0:0:0: Attached scsi CD-ROM sr1
[16843.861983] sr 6:0:0:0: Attached scsi generic sg3 type 5
[17721.987767] perf: interrupt took too long (4140 > 4021), lowering kernel.perf_event_max_sample_rate to 48250
[18599.486730] usb 2-1.1: USB disconnect, device number 7
[18915.353160] usb 2-1.1: new high-speed USB device number 8 using ehci-pci
[18915.465844] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=1a2b
[18915.465847] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[18915.465849] usb 2-1.1: Product: DISK
[18915.465851] usb 2-1.1: Manufacturer: Realtek
[18915.466171] usb-storage 2-1.1:1.0: USB Mass Storage device detected
[18915.467352] scsi host6: usb-storage 2-1.1:1.0
[18916.660690] scsi 6:0:0:0: CD-ROM            RTK      Driver Storage   2.03 PQ: 0 ANSI: 0 CCS
[18916.664615] sr 6:0:0:0: [sr1] scsi3-mmc drive: 0x/0x caddy
[18916.664944] sr 6:0:0:0: Attached scsi CD-ROM sr1
[18916.665119] sr 6:0:0:0: Attached scsi generic sg3 type 5
laurent@MSI-GT780DX:~$ 
laurent@MSI-GT780DX:~$ sudo rfkill list
0: phy0: Wireless LAN
        Soft blocked: no
        Hard blocked: no
laurent@MSI-GT780DX:~$ iw dev
phy#0
        Interface wlp3s0
                ifindex 3
                wdev 0x1
                addr dc:a9:71:be:9b:7d
                ssid Freebox-9F39BF
                type managed
                channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
laurent@MSI-GT780DX:~$

Il ne trouve que le wifi intégré dans le portable par defaut :

laurent@MSI-GT780DX:~$ iwconfig
enp2s0    no wireless extensions.

lo        no wireless extensions.

wlp3s0    IEEE 802.11  ESSID:"Freebox-9F39BF"  
          Mode:Managed  Frequency:2.462 GHz  Access Point: 14:0C:76:9F:39:C0   
          Bit Rate=65 Mb/s   Tx-Power=15 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          Link Quality=60/70  Signal level=-50 dBm  
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:326   Missed beacon:0

laurent@MSI-GT780DX:~$ 

Pouvez vous m'aidez, m'aiguiller pour installer ma lé usb Wifi 6E sur Ubuntu 16.04.5 ?
Merci d'avance pour vos avis et conseils.

Dernière modification par xunil2003 (Le 24/08/2023, à 15:59)


- AMD R9 5950x 64 Go Ram / Intel Pentium I7 960 - 12 Go Ram - 6 T0 - Kubuntu 12.04 x64 / Kubuntu 14.04 x64 / Kubuntu 16.04 x64 / Kubuntu 18.04 x64 /  Kubuntu 20.04 x64 / Mint
- DreamPlug Multi Boot / Marvel 1.22 Ghz / Architecture ARM / 512 Mo Ram / Carte-sd 16 Go class 10 / 5 Watts / Debian Squeeze 2.6.39.4
- Raspberry PI 1 / Raspberry PI 2 / Raspberry PI 3 / Raspberry PI 4 : 4Gb
JE SUIS CHARLIE

Hors ligne

#2 Le 24/08/2023, à 16:09

xubu1957

Re : Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

Bonjour,

Tente cette commande :

sudo usb_modeswitch -KW -v 0bda -p 1a2b

donnée par JeremyB

> DWA-171

C'est pas un modèle facile, voir le fil > Clé wifi non reconnue par ubuntu 18.04lts [RESOLU]


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#3 Le 25/08/2023, à 13:26

xunil2003

Re : Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

Bonjour,

voici le retour

laurent@MSI-GT780DX:~$ sudo usb_modeswitch -KW -v 0bda -p 1a2b
[sudo] Mot de passe de laurent : 
Take all parameters from the command line


 * usb_modeswitch: handle USB devices with multiple modes
 * Version 2.2.5 (C) Josua Dietze 2015
 * Based on libusb1/libusbx

 ! PLEASE REPORT NEW CONFIGURATIONS !

DefaultVendor=  0x0bda
DefaultProduct= 0x1a2b

StandardEject=1
NeedResponse=0

Look for default devices ...
  found USB ID 1770:ff00
  found USB ID 3938:1026
  found USB ID 0bda:0139
   vendor ID matched
  found USB ID 0bda:1a2b
   vendor ID matched
   product ID matched
  found USB ID 8087:0024
  found USB ID 1d6b:0002
  found USB ID 1d6b:0003
  found USB ID 1d6b:0002
  found USB ID 8087:0024
  found USB ID 1d6b:0002
 Found devices in default mode (1)
Access device 003 on bus 002
Current configuration number is 1
Use interface number 0
Use endpoints 0x05 (out) and 0x84 (in)

USB description data (for identification)
-------------------------
Manufacturer: Realtek
     Product: DISK                                                                                                                                                                                                                                                             
  Serial No.: not provided                                                                                                                                                                                                                                                     
-------------------------                                                                                                                                                                                                                                                      
Sending standard EJECT sequence                                                                                                                                                                                                                                                
Looking for active driver ...                                                                                                                                                                                                                                                  
 OK, driver detached                                                                                                                                                                                                                                                           
Set up interface 0                                                                                                                                                                                                                                                             
Use endpoint 0x05 for message sending ...                                                                                                                                                                                                                                      
Trying to send message 1 to endpoint 0x05 ...                                                                                                                                                                                                                                  
 OK, message successfully sent                                                                                                                                                                                                                                                 
Read the response to message 1 (CSW) ...                                                                                                                                                                                                                                       
 Response successfully read (13 bytes).                                                                                                                                                                                                                                        
Trying to send message 2 to endpoint 0x05 ...                                                                                                                                                                                                                                  
 OK, message successfully sent                                                                                                                                                                                                                                                 
Read the response to message 2 (CSW) ...                                                                                                                                                                                                                                       
 Response successfully read (13 bytes).                                                                                                                                                                                                                                        
Reset response endpoint 0x84                                                                                                                                                                                                                                                   
libusb: error [op_clear_halt] clear_halt failed error -1 errno 71                                                                                                                                                                                                              
 Could not reset endpoint (probably harmless): -99                                                                                                                                                                                                                             
Reset message endpoint 0x05                                                                                                                                                                                                                                                    
libusb: error [op_clear_halt] clear_halt failed error -1 errno 71                                                                                                                                                                                                              
 Could not reset endpoint (probably harmless): -99                                                                                                                                                                                                                             
-> Run lsusb to note any changes. Bye!                                                                                                                                                                                                                                         
                                                                                                                                                                                                                                                                               
laurent@MSI-GT780DX:~$     

Merci.


- AMD R9 5950x 64 Go Ram / Intel Pentium I7 960 - 12 Go Ram - 6 T0 - Kubuntu 12.04 x64 / Kubuntu 14.04 x64 / Kubuntu 16.04 x64 / Kubuntu 18.04 x64 /  Kubuntu 20.04 x64 / Mint
- DreamPlug Multi Boot / Marvel 1.22 Ghz / Architecture ARM / 512 Mo Ram / Carte-sd 16 Go class 10 / 5 Watts / Debian Squeeze 2.6.39.4
- Raspberry PI 1 / Raspberry PI 2 / Raspberry PI 3 / Raspberry PI 4 : 4Gb
JE SUIS CHARLIE

Hors ligne

#4 Le 25/08/2023, à 14:47

xubu1957

Re : Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

Bonjour,

Vu :

[   15.108126] VBoxPciLinuxInit

Tu as une virtualisation ou une virtualbox ?


Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne

#5 Le 26/08/2023, à 08:56

xunil2003

Re : Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

Bonjour,

Oui j'ai installer virtualbox, mais je ne comprend pas le rapport avec virtualbox pour faire fonctionner une clé wifi 6E sur mon pc sans virtualisation.

Merci.


- AMD R9 5950x 64 Go Ram / Intel Pentium I7 960 - 12 Go Ram - 6 T0 - Kubuntu 12.04 x64 / Kubuntu 14.04 x64 / Kubuntu 16.04 x64 / Kubuntu 18.04 x64 /  Kubuntu 20.04 x64 / Mint
- DreamPlug Multi Boot / Marvel 1.22 Ghz / Architecture ARM / 512 Mo Ram / Carte-sd 16 Go class 10 / 5 Watts / Debian Squeeze 2.6.39.4
- Raspberry PI 1 / Raspberry PI 2 / Raspberry PI 3 / Raspberry PI 4 : 4Gb
JE SUIS CHARLIE

Hors ligne

#6 Le 26/08/2023, à 09:03

xubu1957

Re : Installer une clé usb Wifi 6E ax3000 sur Ubuntu 16.04

Bonjour,

J'avais un doute.

Les commandes pour compiler le pilote wifi :

Mise en place des outils :

sudo apt install --reinstall git build-essential dkms

récupération du pilote dans le github:

git clone https://github.com/jeremyb31/rtl8821CU.git

puis :

sudo dkms add rtl8821CU
sudo dkms install rtl8821cu/5.2.4

Redémarrage et :

sudo usb_modeswitch -KW -v 0bda -p 1a2b

Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci.                   Membre de Linux-Azur

Hors ligne