Pages : 1
#1 Le 12/05/2022, à 12:49
- Elcellat
initramfs
Bonjour,
Mon portable est planté avec ce message qui apparaît :
BusyBox v1.30.1 (Ubuntu 1:1.30.1-4ubuntu6.4) built-in shell (ash)
Enter 'Help' for a liste of built-in-commands.
(initramfs)
j'ai tapé help mais je n'y comprends rien (texte "touffu" en anglais)
J'ai trouvé une discussion sur initramfs sur le forum mais je ne comprends pas plus .
J'ai une version 20 de Kubuntu installée en février 2021
Faut'il réinstaller une version plus récente ?
Merci pour votre aide.
Hors ligne
#2 Le 12/05/2022, à 13:03
- geole
Re : initramfs
Bonjour
As-tu quelques messages avant ce plantage qui pourraient expliquer?
Avec un support d'installation, lance un boot-info et donne l'URL qui sera générée afin de mieux cerner le problème https://doc.ubuntu-fr.org/tutoriel/boot-info.
Dernière modification par geole (Le 12/05/2022, à 13:04)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#3 Le 12/05/2022, à 17:23
- Elcellat
Re : initramfs
Non je n'ai pas eu de messages avant ce plantage, j'étais sur internet quand c'est arrivé.
J'ai installé Kubuntu à partir d'une clé usb, j'ai réessayé mais ça ne donne rien et je ne comprends pas comment lancer un boot-info malgré la page consacrée à ce sujet.
Hors ligne
#4 Le 12/05/2022, à 17:44
- geole
Re : initramfs
Il faut booter avec la clé USB
Il faut choisir essayer avant d'installer ou quelque chose d'analogue
Il faut ouvrir un terminal en frappant les caractères Ctrl Alt t
Il faut vérifier que le réseau fonctionne
ping -c4 google.com
Puis faire la commande indiquée
sudo add-apt-repository -y ppa:yannubuntu/boot-repair
sudo apt update
sudo apt install -y boot-info
boot-info
et poster l'URL générée
Vu ce que tu racontes, on va aussi contrôler l'état du disque
1) Installation
sudo apt-get install --no-install-recommends smartmontools
2) Poster le retour de cette commande après avoir remplacé sda par ce qui convient si sda n'est pas bon
sudo smartctl -s on -a /dev/sda
Dernière modification par geole (Le 12/05/2022, à 17:45)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#5 Le 12/05/2022, à 18:11
- iznobe
Re : initramfs
Bonjour , dans la console qui apparait , si tu y met :
sudo fsck -fyv /dev/sda1
puis que tu valides , ca dit quoi ? donne le retour stp .
retour utilisable de commande
MSI Z490A-pro , i7 10700 , 32 GB RAM .
Hors ligne
#6 Le 12/05/2022, à 22:51
- Elcellat
Re : initramfs
J'ai booté sur la clé usb avec laquelle j'avais installé kubuntu mais ça ne fonctionne pas (=failed to load ldlinux.c32)
Faut'il télécharger un fichier uniquement pour booter ?
Quand je démarre sur le disque dur voilà l'écran que j'obtiens :
Quand je tape c j'arrive sous grub>
quand je les lignes de commandes à partir de là = can't find sudo........
Hors ligne
#7 Le 12/05/2022, à 23:07
- iznobe
Re : initramfs
Dans ce menu , choisis la 2eme ligne : advanced options for ubuntu .
puis descend sur le choix avec le noyau avec les numeros les plus bas , puis valide pour voir si ca demarre normalement .
retour utilisable de commande
MSI Z490A-pro , i7 10700 , 32 GB RAM .
Hors ligne
#8 Le 13/05/2022, à 03:08
- nany
Re : initramfs
Bonjour,
Juste pour dire que,
sudo fsck -fyv /dev/sda1
en console BusyBox (initramfs) on est en root donc pas besoin de sudo.
Hors ligne
#9 Le 13/05/2022, à 07:40
- iznobe
Re : initramfs
Bonjour @nany , arf oui c ' est vrai
retour utilisable de commande
MSI Z490A-pro , i7 10700 , 32 GB RAM .
Hors ligne
#10 Le 13/05/2022, à 09:50
- geole
Re : initramfs
J'ai booté sur la clé usb avec laquelle j'avais installé kubuntu mais ça ne fonctionne pas (=failed to load ldlinux.c32)
Faut'il télécharger un fichier uniquement pour booter ?....
Bonjour.
Cela semble vouloir dire que la clé USB n'est plus correctement lisible. Le plus simple est de la refabriquer avec un autre ordinateur. Tu pourras en profiter pour télécharger le dernier ISO https://www.ubuntu-fr.org/download/
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#11 Le 17/05/2022, à 19:54
- Elcellat
Re : initramfs
Bonsoir,
J'ai refabriqué une clé bootable qui fonctionne et j'ai tenté de réinstaller Kubuntu mais quand je redémarre l'ordi sur le DD, j'ai un message qui m'indique que "is failed".
En démarrant sur la clé j'ai réussi à taper les différentes formules que vous m'avez indiquées, voilà ce que ça donne :
kubuntu@kubuntu:~$ apt-get install --no-install-recommends smartmontools
E: Impossible d'ouvrir le fichier verrou /var/lib/dpkg/lock-frontend - open (13: Permission denied)
E: Impossible d'obtenir le verrou de dpkg (/var/lib/dpkg/lock-frontend). Avez-vous les droits du superutilisateur ?
kubuntu@kubuntu:~$ sudo smartctl -s on -a /dev/sda
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.15.0-25-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, [url=http://www.smartmontools.org]www.smartmontools.org[/url]
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MK..76GSX
Device Model: TOSHIBA MK6476GSX
Serial Number: Z2JHC1DUT
LU WWN Device Id: 5 000039 473b04ff7
Firmware Version: GS001M
User Capacity: 640135028736 bytes [640 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Tue May 17 17:19:33 2022 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 203) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1967
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 2540
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Minutes 0x0032 095 095 000 Old_age Always - 33h+28m
10 Spin_Retry_Count 0x0033 150 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 2511
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 123
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 59
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 5573
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Min/Max 9/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 54
222 Loaded_Hours 0x0032 096 096 000 Old_age Always - 1893
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 310
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 1503 hours (62 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 41 00 87 c2 81 61 Error: ICRC, ABRT at LBA = 0x0181c287 = 25281159
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 80 00 08 c2 81 40 00 00:02:00.606 WRITE FPDMA QUEUED
61 80 00 88 c1 81 40 00 00:02:00.573 WRITE FPDMA QUEUED
61 80 00 08 c1 81 40 00 00:02:00.550 WRITE FPDMA QUEUED
61 80 00 88 c0 81 40 00 00:02:00.543 WRITE FPDMA QUEUED
61 80 00 08 c0 81 40 00 00:02:00.505 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
kubuntu@kubuntu:~$ sudo fsck -fyv /dev/sda1
fsck from util-linux 2.37.2
e2fsck 1.46.5 (30-Dec-2021)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sda1
The superblock could not be read or does not describe a valid ext2/ext3/ext4
filesystem. If the device is valid and it really contains an ext2/ext3/ext4
filesystem (and not swap or ufs or something else), then the superblock
is corrupt, and you might try running e2fsck with an alternate superblock:
e2fsck -b 8193 <device>
or
e2fsck -b 32768 <device>
Dernière modification par Elcellat (Le 18/05/2022, à 18:08)
Hors ligne
#12 Le 17/05/2022, à 19:57
- xubu1957
Re : initramfs
Bonjour,
Comme demandé dans le premier message du tutoriel Retour utilisable de commande
Pour ajouter toi-même les balises code à ton précédent message #11 : Merci
Cliquer sur le lien « Modifier » en bas à droite du message
Sélectionner le texte
Cliquer sur le <> de l'éditeur de message
Dernière modification par xubu1957 (Le 30/05/2022, à 18:24)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#13 Le 18/05/2022, à 00:48
- geole
Re : initramfs
Bonsoir.
L'état matériel du disque ne semble pas en cause bien que le compteur 220 ne me plaise pas. https://kb.acronis.com/content/9148 La température n'a jamais été excessive et que seulement 123 chocs (compteur 191)
Il faut booter avec la clé USB
Il faut choisir essayer avant d'installer ou quelque chose d'analogue
Il faut ouvrir un terminal en frappant les caractères Ctrl Alt t
Il faut vérifier que le réseau fonctionneping -c4 google.com
Puis faire la commande indiquée
sudo add-apt-repository -y ppa:yannubuntu/boot-repair
sudo apt update
sudo apt install -y boot-info
boot-info
et poster l'URL générée
"mais quand je redémarre l'ordi sur le DD, j'ai un message qui m'indique que "is failed".
Qu'est-ce qui est en échec?
Dernière modification par geole (Le 18/05/2022, à 01:17)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#14 Le 18/05/2022, à 18:02
- Elcellat
Re : initramfs
Bonsoir,
C'est le disque dur qui est en échec.
Hors ligne
#15 Le 18/05/2022, à 19:44
- geole
Re : initramfs
Bonsoir
C'est le message exact? ou une traduction de ta part?..
Car, ici il n'y a pas de problème physique
kubuntu@kubuntu:~$ sudo fsck -fyv /dev/sda1
fsck from util-linux 2.37.2
e2fsck 1.46.5 (30-Dec-2021)
ext2fs_open2: Bad magic number in super-block
fsck.ext2: Superblock invalid, trying backup blocks...
fsck.ext2: Bad magic number in super-block while trying to open /dev/sda1
Probablement une erreur de n° de partition
Toujours pas eu le boot-info?
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#16 Le 19/05/2022, à 11:09
- Elcellat
Re : initramfs
Bonjour,
Voici l'URL générée par le boot-info : https://paste.ubuntu.com/p/DvYGYpF4Dm/
Merci pour votre aide
Hors ligne
#17 Le 19/05/2022, à 11:12
- xubu1957
Re : initramfs
Bonjour,
Collage du Boot-info :
boot-info-4ppa200 [20220519_0903]
============================== Boot Info Summary ===============================
=> Grub2 (v2.00) is installed in the MBR of /dev/sda and looks at sector 2048
of the same hard drive for core.img. core.img is at this location and
looks for (,gpt3)/boot/grub. It also embeds following components:
modules
---------------------------------------------------------------------------
fshelp ext2 part_gpt biosdisk
---------------------------------------------------------------------------
=> Grub2 (v2.00) is installed in the MBR of /dev/sdb and looks at sector 1 of
the same hard drive for core.img. core.img is at this location and looks
for (hd0,msdos1)/boot/grub. It also embeds following components:
modules
---------------------------------------------------------------------------
biosdisk fshelp fat exfat ext2 ntfs ntfscomp part_msdos
---------------------------------------------------------------------------
sda1: __________________________________________________________________________
File system: BIOS Boot partition
Boot sector type: Grub2's core.img
Boot sector info:
sda2: __________________________________________________________________________
File system: vfat
Boot sector type: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /efi/BOOT/fbx64.efi /efi/BOOT/mmx64.efi
/efi/ubuntu/grubx64.efi /efi/ubuntu/mmx64.efi
/efi/ubuntu/shimx64.efi /efi/ubuntu/grub.cfg
sda3: __________________________________________________________________________
File system: ext4
Boot sector type: -
Boot sector info:
Operating System: Ubuntu 22.04 LTS
Boot files: /boot/grub/grub.cfg /etc/fstab /etc/default/grub
/boot/grub/i386-pc/core.img
sdb1: __________________________________________________________________________
File system: vfat
Boot sector type: MSWIN4.1: FAT32
Boot sector info: No errors found in the Boot Parameter Block.
Operating System:
Boot files: /boot/grub/grub.cfg /efi/boot/bootx64.efi
/efi/boot/grubx64.efi /efi/boot/mmx64.efi
================================ 1 OS detected =================================
OS#1: Ubuntu 22.04 LTS on sda3
================================ Host/Hardware =================================
CPU architecture: 64-bit
Video: Park [Mobility Radeon HD 5430/5450/5470] from Advanced Micro Devices, Inc. [AMD/ATI]
Live-session OS is Ubuntu 64-bit (Ubuntu 22.04 LTS, jammy, x86_64)
===================================== UEFI =====================================
BIOS/UEFI firmware: 1.30(1.30) from TOSHIBA
The firmware seems EFI-compatible, but this live-session is in Legacy/BIOS/CSM mode (not in EFI mode).
c152ec201c37b6e97bbc2207e49d1271 sda2/BOOT/fbx64.efi
fdafb5eece6caeccb788c946a28e6872 sda2/BOOT/mmx64.efi
f62c28d9b477b6a1a7b1c991b2b6637d sda2/ubuntu/grubx64.efi
fdafb5eece6caeccb788c946a28e6872 sda2/ubuntu/mmx64.efi
728124f6ec8e22fbdbe7034812c81b95 sda2/ubuntu/shimx64.efi
728124f6ec8e22fbdbe7034812c81b95 sda2/BOOT/BOOTX64.efi
============================= Drive/Partition Info =============================
Disks info: ____________________________________________________________________
sda : is-GPT, hasBIOSboot, has---ESP, not-usb, not-mmc, has-os, no-wind, 2048 sectors * 512 bytes
Partitions info (1/3): _________________________________________________________
sda2 : no-os, 32, nopakmgr, no-docgrub, nogrub, nogrubinstall, no-grubenv, noupdategrub, not-far
sda3 : is-os, 64, apt-get, signed grub-pc grub-efi , grub2, grub-install, grubenv-ok, update-grub, farbios
Partitions info (2/3): _________________________________________________________
sda2 : is---ESP, part-has-no-fstab, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot
sda3 : isnotESP, fstab-has-goodEFI, no-nt, no-winload, no-recov-nor-hid, no-bmgr, notwinboot
Partitions info (3/3): _________________________________________________________
sda2 : not--sepboot, no---boot, part-has-no-fstab, not-sep-usr, no---usr, part-has-no-fstab, no--grub.d, sda
sda3 : not--sepboot, with-boot, fstab-without-boot, not-sep-usr, with--usr, fstab-without-usr, std-grub.d, sda
fdisk -l (filtered): ___________________________________________________________
Disk sda: 596.17 GiB, 640135028736 bytes, 1250263728 sectors
Disk identifier: 1A7822F0-8827-4D3E-AA01-9B92FB7B58E7
Start End Sectors Size Type
sda1 2048 4095 2048 1M BIOS boot
sda2 4096 1054719 1050624 513M EFI System
sda3 1054720 1250263039 1249208320 595.7G Linux filesystem
Disk sdb: 28.88 GiB, 31004295168 bytes, 60555264 sectors
Disk identifier: 0x06feb40b
Boot Start End Sectors Size Id Type
sdb1 * 2048 60555263 60553216 28.9G c W95 FAT32 (LBA)
parted -lm (filtered): _________________________________________________________
sda:640GB:scsi:512:512:gpt:ATA TOSHIBA MK6476GS:;
1:1049kB:2097kB:1049kB:::bios_grub;
2:2097kB:540MB:538MB:fat32:EFI System Partition:boot, esp;
3:540MB:640GB:640GB:ext4::;
sdb:31.0GB:scsi:512:512:msdos:Terra USThree:;
1:1049kB:31.0GB:31.0GB:fat32::boot, lba;
blkid (filtered): ______________________________________________________________
NAME FSTYPE UUID PARTUUID LABEL PARTLABEL
sda
├─sda1 66f6e056-a011-4de7-a5a4-11f01fbee487
├─sda2 vfat 7B6C-D4DD 6a13cccf-fd5e-40d6-8b4d-c3e8ea61f5f2 EFI System Partition
└─sda3 ext4 7771c458-34e7-4f85-9c2e-b72f899606ad 25f9bf1f-1ac0-424c-89c1-efbe91eb708c
sdb
└─sdb1 vfat A85E-06DE 06feb40b-01 KUBUNTU 22_
sdc
Mount points (filtered): _______________________________________________________
Avail Use% Mounted on
/dev/sda2 506.7M 1% /mnt/boot-sav/sda2
/dev/sda3 546G 2% /mnt/boot-sav/sda3
/dev/sdb1 25.4G 12% /cdrom
Mount options (filtered): ______________________________________________________
/dev/sda2 vfat rw,relatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro
/dev/sda3 ext4 rw,relatime
/dev/sdb1 vfat ro,noatime,fmask=0022,dmask=0022,codepage=437,iocharset=iso8859-1,shortname=mixed,errors=remount-ro
===================== sda2/efi/ubuntu/grub.cfg (filtered) ======================
search.fs_uuid 7771c458-34e7-4f85-9c2e-b72f899606ad root hd0,gpt3
set prefix=($root)'/boot/grub'
configfile $prefix/grub.cfg
====================== sda3/boot/grub/grub.cfg (filtered) ======================
Ubuntu 7771c458-34e7-4f85-9c2e-b72f899606ad
Ubuntu, with Linux 5.15.0-30-generic 7771c458-34e7-4f85-9c2e-b72f899606ad
Ubuntu, with Linux 5.15.0-25-generic 7771c458-34e7-4f85-9c2e-b72f899606ad
### END /etc/grub.d/30_os-prober ###
### END /etc/grub.d/30_uefi-firmware ###
========================== sda3/etc/fstab (filtered) ===========================
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda3 during installation
UUID=7771c458-34e7-4f85-9c2e-b72f899606ad / ext4 errors=remount-ro 0 1
# /boot/efi was on /dev/sda2 during installation
UUID=7B6C-D4DD /boot/efi vfat umask=0077 0 1
/swapfile none swap sw 0 0
======================= sda3/etc/default/grub (filtered) =======================
GRUB_DEFAULT=0
GRUB_TIMEOUT_STYLE=hidden
GRUB_TIMEOUT=0
GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian`
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX=""
==================== sda3: Location of files loaded by Grub ====================
GiB - GB File Fragment(s)
380,695152283 = 408,768307200 boot/grub/grub.cfg 1
208,930637360 = 224,337563648 boot/grub/i386-pc/core.img 1
210,122608185 = 225,617432576 boot/vmlinuz 1
5,666988373 = 6,084882432 boot/vmlinuz-5.15.0-25-generic 2
210,122608185 = 225,617432576 boot/vmlinuz-5.15.0-30-generic 1
5,666988373 = 6,084882432 boot/vmlinuz.old 2
211,265014648 = 226,844082176 boot/initrd.img 2
209,843235016 = 225,317457920 boot/initrd.img-5.15.0-25-generic 1
211,265014648 = 226,844082176 boot/initrd.img-5.15.0-30-generic 2
209,843235016 = 225,317457920 boot/initrd.img.old 1
===================== sda3: ls -l /etc/grub.d/ (filtered) ======================
-rwxr-xr-x 1 root root 18683 Apr 15 21:50 10_linux
-rwxr-xr-x 1 root root 43031 Apr 15 21:50 10_linux_zfs
-rwxr-xr-x 1 root root 14180 Apr 15 21:50 20_linux_xen
-rwxr-xr-x 1 root root 13369 Apr 15 21:50 30_os-prober
-rwxr-xr-x 1 root root 1372 Apr 15 21:50 30_uefi-firmware
-rwxr-xr-x 1 root root 700 Feb 19 13:21 35_fwupd
-rwxr-xr-x 1 root root 214 Apr 15 21:50 40_custom
-rwxr-xr-x 1 root root 215 Apr 15 21:50 41_custom
=========================== sda3/etc/grub.d/35_fwupd ===========================
#! /bin/sh
# SPDX-License-Identifier: LGPL-2.1+
set -e
[ -d ${pkgdatadir:?} ]
# shellcheck source=/dev/null
. "$pkgdatadir/grub-mkconfig_lib"
if [ -f /var/lib/fwupd/uefi_capsule.conf ] &&
ls /sys/firmware/efi/efivars/fwupd-*-0abba7dc-e516-4167-bbf5-4d9d1c739416 1>/dev/null 2>&1; then
. /var/lib/fwupd/uefi_capsule.conf
if [ "${EFI_PATH}" != "" ] && [ "${ESP}" != "" ]; then
echo "Adding Linux Firmware Updater entry" >&2
cat << EOF
menuentry 'Linux Firmware Updater' \$menuentry_id_option 'fwupd' {
EOF
${grub_probe:?}
prepare_grub_to_access_device '`${grub_probe} --target=device \${ESP}` | sed -e "s/^/\t/"'
cat << EOF
chainloader ${EFI_PATH}
}
EOF
fi
fi
====================== sdb1/boot/grub/grub.cfg (filtered) ======================
Try or Install Kubuntu
Kubuntu (safe graphics)
OEM install (for manufacturers)
Boot from next volume
UEFI Firmware Settings
Test memory
==================== sdb1: Location of files loaded by Grub ====================
GiB - GB File Fragment(s)
?? = ?? boot/grub/grub.cfg 1
Suggested repair: ______________________________________________________________
The default repair of the Boot-Repair utility would reinstall the grub-efi of
sda3,
using the following options: sda2/boot/efi
Additional repair would be performed: unhide-bootmenu-10s use-standard-efi-file
Blockers in case of suggested repair: __________________________________________
The current session is in BIOS-compatibility mode. Please disable BIOS-compatibility/CSM/Legacy mode in your UEFI firmware, and use this software from a live-CD (or live-USB) that is compatible with UEFI booting mode. For example, use a live-USB of Boot-Repair-Disk-64bit (www.sourceforge.net/p/boot-repair-cd), after making sure your BIOS is set up to boot USB in EFI mode. This will enable this feature.
Final advice in case of suggested repair: ______________________________________
Please do not forget to make your UEFI firmware boot on the Ubuntu 22.04 LTS entry (sda2/efi/****/grub****.efi (**** will be updated in the final message) file) !
The boot of your PC is in BIOS-compatibility/CSM/Legacy mode. You may want to retry after changing it to UEFI mode.
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#18 Le 19/05/2022, à 11:38
- Elcellat
Re : initramfs
Vu que je n'y comprends rien, quelqu'un peut'il me donner un diagnostic en clair et me dire s'il y a une solution au problème ?
Hors ligne
#19 Le 19/05/2022, à 12:07
- FrancisFDZ
Re : initramfs
Bonjour,
Il faut ouvrir un terminal en frappant les caractères Ctrl Alt t
C'est un raccourci typiquement gnome, je ne suis pas sur qu'il soit universel
[Edit] En fait, plusieurs programmes utilisent ce raccourci, pas forcément pour la même utilisation
Mais sans forcément faire l'unanimité, il est souvent utilisé pour lancer un terminal : XFCE, Deepin (?), Mint, Ubuntu, ...) [//Edit]
Dernière modification par FrancisFDZ (Le 19/05/2022, à 12:16)
-- On peut avoir des raisons de se plaindre et n'avoir pas raison de se plaindre --
[Victor Hugo]
Hors ligne
Pages : 1