Adaptateur Compact Flasdh PCMCIA

Romu · Le 23/03/2005, à 09:31

Bonjour, je suis nouveau sous Linux, venant du monde MS.

J'ai réussi sans problème à installer Warty et Hoary sur mon DELL Inspiron 8600c (portable donc), sauf pour une chose.

J'ai un adaptateur PCMCIA pour lire les cartes CF de mon appareil et quand je mets la carte j'obtiens 2 bips, assez forts, mais rien ne se passe (pas de montage automatique, pas d'accès...).

Une solution serait grandement appréciée.

Merci.

Romu · Le 29/03/2005, à 09:11

Je suis le seul à rencontrer ce problème ?

Toute aide serait grandement appréciée.

coffee · Le 29/03/2005, à 09:52

J'ai pas de modules PCMCIA, j'en ai jamais fait, j'ai pas de lecteurs de cartes et je sais pas ce qu'est une carte CF (enfin si je sais mais je sais pas, je sais juste que c'est une carte de stockage et ça doit suffire pour t'aider) donc ça va être dur de t'aider.

Néanmoins, tu peux nous donner des renseignements supplémentaire avec un lspci et ce que te renvoit dmesg quand tu inseres une carte

Romu · Le 29/03/2005, à 10:00

La commande lscpi je vais essayer, mais pour le log dmesg, le voici :

Linux version 2.6.10-4-386 (buildd@mcmurdo) (gcc version 3.3.5 (Debian 1:3.3.5-8ubuntu2)) #1 Thu Mar 10 03:25:00 GMT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffae000 (usable)
BIOS-e820: 000000001ffae000 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
511MB LOWMEM available.
On node 0 totalpages: 130990
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126894 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fdf00
ACPI: RSDT (v001 DELL CPi R 0x27d4081e ASL 0x00000061) @ 0x1fff0000
ACPI: FADT (v001 DELL CPi R 0x27d4081e ASL 0x00000061) @ 0x1fff0400
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
Built 1 zonelists
Kernel command line: root=/dev/hda2 ro quiet splash
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01405000)
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 598.208 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 511516k/523960k available (1434k kernel code, 11816k reserved, 752k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1183.74 BogoMIPS (lpj=591872)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000
CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 00000180 00000000
CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ACPI: setting ELCR to 0200 (from 0800)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4256k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfc96e, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0x800-0x805 could not be reserved
pnp: 00:01: ioport range 0x808-0x80f could not be reserved
pnp: 00:02: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:02: ioport range 0x806-0x807 has been reserved
pnp: 00:02: ioport range 0x810-0x85f could not be reserved
pnp: 00:02: ioport range 0x860-0x87f has been reserved
pnp: 00:02: ioport range 0x880-0x8bf has been reserved
pnp: 00:02: ioport range 0x8c0-0x8df has been reserved
pnp: 00:07: ioport range 0x900-0x97f has been reserved
audit: initializing netlink socket (disabled)
audit(1112077524.074:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI interrupt 0000:00:1f.6[b] -> GSI 7 (level, low) -> IRQ 7
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
LID PBTN PCI0 USB0 USB1 USB2 USB3 MODM PCIE
ACPI: (supports S0 S1 S3 S4 S4bios S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4256KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (30 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 11 (level, low) -> IRQ 11
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHM2100AT, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB) w/2048KiB Cache, CHS=19485/16/63, UDMA(66)
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 >
Probing IDE interface ide1...
hdc: PHILIPS CD-RW/DVD-ROM CDD5263, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
Stopping tasks: ==|
Freeing memory... -\|/done (460 pages freed)
Restarting tasks... done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 979924k swap on /dev/hda1. Priority:-1 extents:1
EXT3 FS on hda2, internal journal
hdc: ATAPI 4X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio1
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
ts: Compaq touchscreen protocol output
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 128M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 11, io base 0xbf80
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.1[b] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 0xbf40
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:1d.2: Intel Corp. 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 0xbf20
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB/DBM (ICH4/ICH4-M) USB 2.0 EHCI Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem 0xf4fffc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
hw_random: cannot enable RNG, aborting
ACPI: PCI interrupt 0000:00:1f.5[b] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49478 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:1f.6[b] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.6 to 64
b44.c:v0.95 (Aug 3, 2004)
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 11 (level, low) -> IRQ 11
eth0: Broadcom 4400 10/100BaseT Ethernet 00:0f:1f:29:68:ca
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:02:01.0 [1028:0191]
Yenta: ISA IRQ mask 0x0478, PCI irq 11
Socket status: 30000010
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:01.1[A] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[faffd800-faffdfff] Max Packet=[2048]
ieee80211_crypt: registered algorithm 'NULL'
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, 1.0.2
ipw2100: Copyright(c) 2003-2004 Intel Corporation
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 7 (level, low) -> IRQ 7
ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
eth1: Radio is disabled by RF switch.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[444fc000080ca830]
cs: pcmcia_socket0: time out after reset.
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ibm_acpi: ec object not found
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
apm: BIOS not found.
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02ef500(lo)
IPv6 over IPv4 tunneling driver

coffee · Le 29/03/2005, à 10:17

et c'est où que tu insère ton lecteur de carte et ta carte?

Romu · Le 29/03/2005, à 10:25

Comment ça "c'est où" ?

C'est un lecteur de carte CF au format PCMCIA, donc la réponse est "dans un slot PCMCIA".

coffee · Le 29/03/2005, à 10:32

mdr oui en effet mais je voulais dire dans le fichier

cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.

là tu insère une carte ou le lecteur?

Romu · Le 29/03/2005, à 10:48

Coffee, c'est super sympa de t'occuper de mon (il y en a au moins 1), mais j'avoue que tu me parles un peu Chinois.

Si je comprends bien ta question, alors la réponse est :
le lecteur est en permanence dans le PC, je n'insère donc que la carte.

Mais ta question m'amène à faire le test suivant : sortir le lecteur, insérer la carte dedans, insérer le tout dans le PC.

Petite question pour ma culture perso, le log dmesg est renseigné en temps réel ou juste au démarrage du PC ? C'est juste histoire d'éviter d'envoyer les 300 lignes quand seules quelques unes suffisent.

Kagou · Le 29/03/2005, à 11:01

cs: pcmcia_socket0: time out after reset.

Ca me plait pas .....

Utilise "tail -f /var/log/messages" pour regarder les messages de ton kernel et insère une carte CF pour voir ce qu'il te dit.
++

Romu · Le 30/03/2005, à 08:29

Après plusieurs tests il apparaît la chose suivante :
- si après insertion je n'obtiens qu'un seul Bip, alors rien ne se passe et rien n'est ajouté au fichier "messages",
- si j'ai 2 ou 3 bips, alors les lignes suivantes sont ajoutées :
Mar 29 21:44:07 localhost kernel: hde: SanDisk SDCFB-48, CFA DISK drive
Mar 29 21:44:07 localhost kernel: ide2 at 0x100-0x107,0x10e on irq 3
Mar 29 21:44:07 localhost kernel: hde: max request size: 128KiB
Mar 29 21:44:07 localhost kernel: hde: 93952 sectors (48 MB) w/1KiB Cache, CHS=734/4/32
Mar 29 21:44:07 localhost kernel: /dev/ide/host2/bus0/target0/lun0: p1
Mar 29 21:44:07 localhost kernel: ide-cs: hde: Vcc = 3.3, Vpp = 0.0
Mar 29 21:44:07 localhost kernel: hde: SanDisk SDCFB-48, CFA DISK drive
Mar 29 21:44:07 localhost kernel: ide2 at 0x100-0x107,0x10e on irq 3
Mar 29 21:44:07 localhost kernel: hde: max request size: 128KiB

En l'occurence pour une carte SanDisk de 48 Mo.Ou :
Mar 29 21:53:22 localhost kernel: hde: SanDisk SDCFH-256, CFA DISK drive
Mar 29 21:53:22 localhost kernel: ide2 at 0x100-0x107,0x10e on irq 3
Mar 29 21:53:22 localhost kernel: hde: max request size: 128KiB
Mar 29 21:53:22 localhost kernel: hde: 501760 sectors (256 MB) w/1KiB Cache, CHS=980/16/32
Mar 29 21:53:22 localhost kernel: /dev/ide/host2/bus0/target0/lun0: p1
Mar 29 21:53:22 localhost kernel: ide-cs: hde: Vcc = 3.3, Vpp = 0.0
Mar 29 21:53:22 localhost kernel: hde: SanDisk SDCFH-256, CFA DISK drive

Pour une SanDisk Ultra 256 Mo.

J'ai essayé une commande du genre "mount /dev/hde1 /cflash vfat defaults,user,noauto 0 0", mais j'ai "Permission non accordée" que je lance cette commande depuis ma console ou depuis celle de root. Sachant que je fais parti du groupe "plugdev".

Il s'avère aussi que ces insertions/extraction me vérolent un peu le système qui n'est alors plus capable de monter automatiquement une simple clé ou lecteur USB, chose qui marche très bien en temps normal.

Si quelqu'un arrive à me faire avancer, c'est super cool.
Merci encore.

coffee · Le 30/03/2005, à 09:41

Romu a écrit :

Petite question pour ma culture perso, le log dmesg est renseigné en temps réel ou juste au démarrage du PC ? C'est juste histoire d'éviter d'envoyer les 300 lignes quand seules quelques unes suffisent.

Temps réel

coffee · Le 30/03/2005, à 09:42

un petit ls /dev/hde*

Romu · Le 03/04/2005, à 17:41

Excusez moi de déranger encore un peu, mais je n'avance pas beaucoup tout seul. Avec la Hoary RC, c'est un peu mieux, j'obtiens les lignes suivantes dans le var/log/messages :
Apr 3 18:24:06 localhost kernel: cs: memory probe 0xa0000000-0xa0ffffff: clean.
Apr 3 18:24:06 localhost kernel: hde: SanDisk SDCFH-1024, CFA DISK drive
Apr 3 18:24:07 localhost kernel: ide2 at 0x100-0x107,0x10e on irq 3
Apr 3 18:24:07 localhost kernel: hde: max request size: 128KiB
Apr 3 18:24:07 localhost kernel: hde: 2001888 sectors (1024 MB) w/1KiB Cache, CHS=1986/16/63
Apr 3 18:24:07 localhost kernel: /dev/ide/host2/bus0/target0/lun0: p1
Apr 3 18:24:07 localhost kernel: ide-cs: hde: Vcc = 3.3, Vpp = 0.0
Apr 3 18:31:26 localhost kernel: /dev/ide/host2/bus0/target0/lun0: p1

Il me reste plus qu'à connaître le point de montage à partir de ces quelques lignes et normalement tout sera ok.

Merci à vous.

Ubuntu-fr

Navigation

Liens de recherche

Annonce

#1 Le 23/03/2005, à 09:31

Adaptateur Compact Flasdh PCMCIA

#2 Le 29/03/2005, à 09:11

Re : Adaptateur Compact Flasdh PCMCIA

#3 Le 29/03/2005, à 09:52

Re : Adaptateur Compact Flasdh PCMCIA

#4 Le 29/03/2005, à 10:00

Re : Adaptateur Compact Flasdh PCMCIA

#5 Le 29/03/2005, à 10:17

Re : Adaptateur Compact Flasdh PCMCIA

#6 Le 29/03/2005, à 10:25

Re : Adaptateur Compact Flasdh PCMCIA

#7 Le 29/03/2005, à 10:32

Re : Adaptateur Compact Flasdh PCMCIA

#8 Le 29/03/2005, à 10:48

Re : Adaptateur Compact Flasdh PCMCIA

#9 Le 29/03/2005, à 11:01

Re : Adaptateur Compact Flasdh PCMCIA

#10 Le 30/03/2005, à 08:29

Re : Adaptateur Compact Flasdh PCMCIA

#11 Le 30/03/2005, à 09:41

Re : Adaptateur Compact Flasdh PCMCIA

#12 Le 30/03/2005, à 09:42

Re : Adaptateur Compact Flasdh PCMCIA

#13 Le 03/04/2005, à 17:41

Re : Adaptateur Compact Flasdh PCMCIA

Pied de page des forums