Pages : 1
#1 Le 18/01/2008, à 12:57
- dandrz
(Débutant) Gusty qui gèle qaund le wifi est utilisé
Bonjour,
suite à un post das le forum général (http://forum.ubuntu-fr.org/viewtopic.php?id=183699), il ma été conseillé de poster mon pb ici.
En résumé, ma config gèle de façon aléatoire et complète quand je suis connecté en wifi.
Voici les sorties des commandes qui sont demandées.
daniel@Danuntu:~$ cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=7.10
DISTRIB_CODENAME=gutsy
DISTRIB_DESCRIPTION="Ubuntu 7.10"daniel@Danuntu:~$ lsusb
Bus 003 Device 003: ID 13fe:1d23
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 003: ID 045e:008c Microsoft Corp. Wireless Intellimouse Explorer 2.0
Bus 001 Device 001: ID 0000:0000daniel@Danuntu:~$ lspci
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1)
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2)
00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2)
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2)
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2)
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600]
01:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary)
02:06.0 Ethernet controller: Atheros Communications, Inc. AR5212/AR5213 Multiprotocol MAC/baseband processor (rev 01)daniel@Danuntu:~$ sudo lshw -C network
[sudo] password for daniel:
*-network
description: Wireless interface
product: AR5212/AR5213 Multiprotocol MAC/baseband processor
vendor: Atheros Communications, Inc.
physical id: 6
bus info: pci@0000:02:06.0
logical name: wifi0
version: 01
serial: 00:15:e9:83:4b:8c
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list logical ethernet physical wireless
configuration: broadcast=yes driver=ath_pci driverversion=0.9.4.5 (0.9.3.2) ip=192.168.1.2 latency=168 maxlatency=28 mingnt=10 module=ath_pci multicast=yes wireless=IEEE 802.11g
daniel@Danuntu:~$ lsmod
Module Size Used by
wlan_tkip 13696 3
af_packet 24840 4
nls_iso8859_1 5120 1
nls_cp437 6784 1
vfat 14080 1
fat 54300 1 vfat
usb_storage 73024 1
libusual 18448 1 usb_storage
radeon 125472 0
drm 83348 1 radeon
rfcomm 42136 2
l2cap 26240 11 rfcomm
bluetooth 57060 4 rfcomm,l2cap
ppdev 10244 0
cpufreq_ondemand 9612 0
cpufreq_conservative 8072 0
cpufreq_userspace 5280 0
cpufreq_powersave 2688 0
cpufreq_stats 7232 0
freq_table 5792 2 cpufreq_ondemand,cpufreq_stats
ac 6148 0
video 18060 0
dock 10656 0
button 8976 0
container 5504 0
sbs 19592 0
battery 11012 0
lp 12580 0
loop 19076 0
nvidia_agp 9756 0
snd_intel8x0 34972 1
snd_ac97_codec 100644 1 snd_intel8x0
ac97_bus 3200 1 snd_ac97_codec
snd_pcm_oss 44672 0
snd_mixer_oss 17664 1 snd_pcm_oss
snd_pcm 80388 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy 4740 0
wlan_scan_sta 15104 1
snd_seq_oss 33152 0
ath_rate_sample 14208 1
ath_pci 98336 0
wlan 206660 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci
snd_seq_midi 9600 0
snd_rawmidi 25728 1 snd_seq_midi
snd_seq_midi_event 8448 2 snd_seq_oss,snd_seq_midi
ath_hal 192720 3 ath_rate_sample,ath_pci
psmouse 39952 0
serio_raw 8068 0
snd_seq 53232 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24324 2 snd_pcm,snd_seq
snd_seq_device 9228 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
pcspkr 4224 0
parport_pc 37412 1
parport 37448 3 ppdev,lp,parport_pc
k8temp 6656 0
shpchp 34580 0
pci_hotplug 32704 1 shpchp
snd 54660 12 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 8800 1 snd
snd_page_alloc 11400 2 snd_intel8x0,snd_pcm
i2c_nforce2 7040 0
i2c_core 26112 1 i2c_nforce2
amd64_agp 13700 0
agpgart 35016 3 drm,nvidia_agp,amd64_agp
evdev 11136 3
sg 36764 0
sd_mod 30336 2
ext3 133896 2
jbd 60456 1 ext3
mbcache 9732 1 ext3
ide_cd 32672 0
cdrom 37536 1 ide_cd
ide_disk 18560 5
usbhid 29536 0
hid 28928 1 usbhid
sata_nv 20612 0
amd74xx 15260 0 [permanent]
ide_core 116804 4 usb_storage,ide_cd,ide_disk,amd74xx
forcedeth 51592 0
ata_generic 8452 0
libata 125168 2 sata_nv,ata_generic
scsi_mod 147084 4 usb_storage,sg,sd_mod,libata
ehci_hcd 36492 0
ohci_hcd 22916 0
usbcore 138632 6 usb_storage,libusual,usbhid,ehci_hcd,ohci_hcd
thermal 14344 0
processor 32072 1 thermal
fan 5764 0
fuse 47124 3
apparmor 40728 0
commoncap 8320 1 apparmordaniel@Danuntu:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11g ESSID:"xxxxxx" Nickname:""
Mode:Managed Frequency:2.452 GHz Access Point: 00:1B:2F:50:9B:74
Bit Rate:36 Mb/s Tx-Power:18 dBm Sensitivity=1/1
Retry:off RTS thr:off Fragment thr:off
Power Management:off
Link Quality=30/70 Signal level=-60 dBm Noise level=-90 dBm
Rx invalid nwid:1941 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0daniel@Danuntu:~$ ifconfig
ath0 Lien encap:Ethernet HWaddr 00:15:E9:83:4B:8C
inet adr:192.168.1.2 Bcast:192.168.1.255 Masque:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:5 erreurs:0 :0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:1088 (1.0 KB) Octets transmis:2900 (2.8 KB)
eth0 Lien encap:Ethernet HWaddr 00:13:8F:88:9F:17
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 b) Octets transmis:0 (0.0 b)
Interruption:9 Adresse de base:0xe000
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:0 (0.0 b) Octets transmis:0 (0.0 b)
wifi0 Lien encap:UNSPEC HWaddr 00-15-E9-83-4B-8C-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:3285 erreurs:0 :0 overruns:0 frame:6002
TX packets:96 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:199
Octets reçus:347340 (339.1 KB) Octets transmis:8054 (7.8 KB)
Interruption:9daniel@Danuntu:~$ uname -r -m
2.6.22-14-generic i686daniel@Danuntu:~$ cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
daniel@Danuntu:~$
daniel@Danuntu:~$ iwconfig ath0
ath0 IEEE 802.11g ESSID:"GABOU" Nickname:""
Mode:Managed Frequency:2.452 GHz Access Point: 00:1B:2F:50:9B:74
Bit Rate:18 Mb/s Tx-Power:18 dBm Sensitivity=1/1
Retry:off RTS thr:off Fragment thr:off
Power Management:off
Link Quality=30/70 Signal level=-59 dBm Noise level=-89 dBm
Rx invalid nwid:4779 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0Bon voilà , j'aimerais utiliser Ubuntu par curiosité intellectuel et c'est dommage que ça bug autant chez moi.
Je remercie par avance ceux qui pourront m'aider.
#2 Le 19/01/2008, à 01:42
- willy78
Re : (Débutant) Gusty qui gèle qaund le wifi est utilisé
Télécharger madwifi svn
wget http://snapshots.madwifi.org/madwifi-ng-current.tar.gzExtraire madwifi
tar -xvzf madwifi-ng-current.tar.gz
cd madwifi-ng-*Compiler
makeInstaller
sudo make installrebooter
sudo rebootDernière modification par willy78 (Le 19/01/2008, à 01:43)
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
#3 Le 19/01/2008, à 13:09
- dandrz
Re : (Débutant) Gusty qui gèle qaund le wifi est utilisé
bonjour,
merci Willy de ton aide mais ça plante au niveau du make. J'en ai plein le cul de toute façon de cet OS, je formate et libère l'espace. Je laisse Linux aux autres. J'ai autre chose à faire de mes nuits 
A+ et bon courage.
#4 Le 19/01/2008, à 13:27
- willy78
Re : (Débutant) Gusty qui gèle qaund le wifi est utilisé
Salut! 
En fait j'avais oublié une commande!
sudo apt-get install build-essentialMais bon c'est pas pour toi!
Dernière modification par willy78 (Le 19/01/2008, à 13:28)
Quelques tutos pour le wifi sous Ubuntu:
http://wlety.free.fr/forum
Hors ligne
Pages : 1