#1 Le 02/09/2023, à 10:22
- H_67
msg i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data .....
Bonjour,
J'ai installé Ubuntu 22.04.3 LTS sur un PC portable Dell Vostro 1220.
J'ai le msg suivant juste avant l'affichage de la page de connexion:
[b]i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data table pointers[/b]massimo@massimo:~$ sudo dmesg –level=err
[b][ 5.640912] i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data table pointers[/b]
[ 25.701055] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 25.701061] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 25.701064] b43-phy0 ERROR: You must go to [url]https://wireless.wiki.kernel.org/en/users/Drivers/b43#devicefirmware[/url] and download the correct firmware for this driver version. Please carefully read all instructions on this website. massimo@massimo:~$ [b]sudo dmesg –level=warn[/b]
[ 0.017442] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/64 (20221020/tbfadt-564)
[ 0.359130] pmd_set_huge: Cannot satisfy [mem 0xf8000000-0xf8200000] with a huge-page mapping due to MTRR override.
[ 0.708172] pnp 00:08: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:00:02.0 BAR 6 [mem 0x000c0000-0x000dffff]
[ 0.909953] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[ 0.910110] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 0.910112] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 0.910115] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 0.910117] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 0.910119] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 0.910121] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 0.910124] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 0.910126] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 0.910128] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 2.716326] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[ 2.716330] clocksource: 'hpet' wd_nsec: 500349031 wd_now: 23187a9 wd_last: 1c436f2 mask: ffffffff
[ 2.716333] clocksource: 'tsc' cs_nsec: 479976147 cs_now: 6f80a62ff cs_last: 6b9422302 mask: ffffffffffffffff
[ 2.716336] clocksource: 'tsc' is current clocksource.
[ 2.728283] TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
[ 2.728395] clocksource: Not enough CPUs to check clocksource 'tsc'.
[ 3.069313] wmi_bus wmi_bus-PNP0C14:00: WQBC data block query control method not found
[ 5.640934] ------------[ cut here ]------------
[ 5.640935] i915 0000:00:02.0: Block 42 min_size is zero
[ 5.640972] WARNING: CPU: 0 PID: 95 at drivers/gpu/drm/i915/display/intel_bios.c:471 init_bdb_block+0x317/0x510 [i915]
[ 5.641337] Modules linked in: i915(+) drm_buddy i2c_algo_bit ttm drm_display_helper cec rc_core drm_kms_helper syscopyarea hid_generic sysfillrect sysimgblt gpio_ich sha512_ssse3 usbhid psmouse hid ums_realtek uas ahci i2c_i801 drm i2c_smbus r8169 libahci lpc_ich usb_storage realtek ssb video wmi
[ 5.641374] CPU: 0 PID: 95 Comm: systemd-udevd Not tainted 6.2.0-31-generic #31~22.04.1-Ubuntu
[ 5.641377] Hardware name: Dell Inc. Vostro 1220 /0X482M, BIOS 1.3.0 10/15/2009
[ 5.641379] RIP: 0010:init_bdb_block+0x317/0x510 [i915]
[ 5.641655] Code: 8b 7b 08 4c 8b 77 50 4d 85 f6 74 29 4c 89 45 d0 e8 ee 33 dd cd 44 89 e1 4c 89 f2 48 c7 c7 68 6a 85 c0 48 89 c6 e8 19 39 40 cd <0f> 0b 4c 8b 45 d0 e9 35 fd ff ff 4c 8b 37 eb d2 4c 89 ee 48 c7 c7
[ 5.641659] RSP: 0018:ffffa6bd80453878 EFLAGS: 00010246
[ 5.641663] RAX: 0000000000000000 RBX: ffff8d25ea968000 RCX: 0000000000000000
[ 5.641665] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 5.641667] RBP: ffffa6bd804538c8 R08: 0000000000000000 R09: 0000000000000000
[ 5.641669] R10: 0000000000000000 R11: 0000000000000000 R12: 000000000000002a
[ 5.641671] R13: 0000000000000000 R14: ffff8d26c0b99f60 R15: 0000000000000000
[ 5.641673] FS: 00007f98c2ae78c0(0000) GS:ffff8d26dbc00000(0000) knlGS:0000000000000000
[ 5.641676] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5.641679] CR2: 000055c43464d470 CR3: 00000000025de000 CR4: 00000000000406f0
[ 5.641681] Call Trace:
[ 5.641684] <TASK>
[ 5.641688] intel_bios_init+0x160/0x3c0 [i915]
[ 5.641950] ? drm_vblank_init+0x6c/0x140 [drm]
[ 5.642031] intel_modeset_init_noirq+0x3a/0x270 [i915]
[ 5.642293] i915_driver_probe+0x10d/0x430 [i915]
[ 5.642483] ? acpi_dev_found+0x66/0x80
[ 5.642490] i915_pci_probe+0xa8/0x1b0 [i915]
[ 5.642685] local_pci_probe+0x4b/0xb0
[ 5.642689] pci_call_probe+0x55/0x190
[ 5.642693] pci_device_probe+0x84/0x120
[ 5.642698] really_probe+0x1ed/0x450
[ 5.642703] __driver_probe_device+0x8a/0x190
[ 5.642707] driver_probe_device+0x23/0xd0
[ 5.642712] __driver_attach+0x10f/0x220
[ 5.642716] ? __pfx___driver_attach+0x10/0x10
[ 5.642721] bus_for_each_dev+0x83/0xe0
[ 5.642724] driver_attach+0x1e/0x30
[ 5.642728] bus_add_driver+0x152/0x250
[ 5.642733] driver_register+0x83/0x160
[ 5.642736] __pci_register_driver+0x68/0x80
[ 5.642739] i915_pci_register_driver+0x23/0x30 [i915]
[ 5.642933] i915_init+0x37/0x120 [i915]
[ 5.643134] ? __pfx_init_module+0x10/0x10 [i915]
[ 5.643335] do_one_initcall+0x49/0x240
[ 5.643341] ? kmalloc_trace+0x2a/0xb0
[ 5.643346] do_init_module+0x52/0x240
[ 5.643351] load_module+0xb96/0xd60
[ 5.643356] __do_sys_finit_module+0xcc/0x150
[ 5.643360] ? __do_sys_finit_module+0xcc/0x150
[ 5.643365] __x64_sys_finit_module+0x18/0x30
[ 5.643369] do_syscall_64+0x5c/0x90
[ 5.643374] ? do_syscall_64+0x69/0x90
[ 5.643378] ? exit_to_user_mode_prepare+0x3b/0xd0
[ 5.643381] ? syscall_exit_to_user_mode+0x2a/0x50
[ 5.643385] ? do_syscall_64+0x69/0x90
[ 5.643388] ? do_syscall_64+0x69/0x90
[ 5.643391] ? do_syscall_64+0x69/0x90
[ 5.643395] ? do_syscall_64+0x69/0x90
[ 5.643398] ? do_syscall_64+0x69/0x90
[ 5.643401] ? sysvec_apic_timer_interrupt+0x4e/0xb0
[ 5.643404] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 5.643408] RIP: 0033:0x7f98c31dfa3d
[ 5.643413] Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d c3 a3 0f 00 f7 d8 64 89 01 48
[ 5.643415] RSP: 002b:00007ffdf27712f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 5.643420] RAX: ffffffffffffffda RBX: 000055c434605af0 RCX: 00007f98c31dfa3d
[ 5.643422] RDX: 0000000000000000 RSI: 00007f98c3376441 RDI: 0000000000000016
[ 5.643424] RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000002
[ 5.643426] R10: 0000000000000016 R11: 0000000000000246 R12: 00007f98c3376441
[ 5.643429] R13: 000055c434662ef0 R14: 000055c434668c50 R15: 000055c43466ed20
[ 5.643433] </TASK>
[ 5.643434] ---[ end trace 0000000000000000 ]---
[ 22.805314] at24 0-0050: supply vcc not found, using dummy regulator
[ 23.926374] dell-smbios A80593CE-A997-11DA-B012-B622A1EF5492: WMI SMBIOS userspace interface not supported(0), try upgrading to a newer BIOS
[ 25.700905] b43 ssb0:0: Direct firmware load for b43/ucode15.fw failed with error -2
[ 25.700959] b43 ssb0:0: Direct firmware load for b43/ucode15.fw failed with error -2
[ 25.701015] b43 ssb0:0: Direct firmware load for b43-open/ucode15.fw failed with error -2
[ 25.701051] b43 ssb0:0: Direct firmware load for b43-open/ucode15.fw failed with error -2
[ 50.558466] kauditd_printk_skb: 61 callbacks suppressedMerci d'avance pour vos solutions
Dernière modification par Ayral (Le 25/01/2024, à 12:11)
Hors ligne
#2 Le 02/09/2023, à 11:28
- H_67
Re : msg i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data .....
Bonjour
Voilà le résultat des commandes :
massimo@massimo:~$ lspci -vnn | grep -A 12 '\''[030[02]\]' | grep -Ei "vga|3d|display|kernel"
uname -a
dpkg -l | grep -v ^ii
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) (prog-if 00 [VGA controller])
Kernel driver in use: i915
Kernel modules: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
Linux massimo 6.2.0-31-generic #31~22.04.1-Ubuntu SMP PREEMPT_DYNAMIC Wed Aug 16 13:45:26 UTC 2 x86_64 x86_64 x86_64 GNU/Linux
Souhait=inconnU/Installé/suppRimé/Purgé/H=à garder
| État=Non/Installé/fichier-Config/dépaqUeté/échec-conFig/H=semi-installé/W=attend-traitement-déclenchements
|/ Err?=(aucune)/besoin Réinstallation (État,Err: majuscule=mauvais)
||/ Nom Version Architecture Description
+++-=============================================-=======================================-============-================================================================================
rc linux-image-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Signed kernel image generic
rc linux-modules-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Linux kernel extra modules for version 5.19.0 on 64 bit x86 SMP
rc linux-modules-extra-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Linux kernel extra modules for version 5.19.0 on 64 bit x86 SMP
massimo@massimo:~$ echo $XDG_SESSION_TYPE
x11Merci pour tout
Dernière modification par Ayral (Le 25/01/2024, à 12:12)
Hors ligne
#3 Le 02/09/2023, à 11:42
- xubu1957
Re : msg i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data .....
Bonjour,
Pour ajouter toi-même les balises code à ton message #1 :
Cliquer sur le lien « Modifier » en bas à droite du message
Sélectionner le texte
Cliquer sur le <> de l'éditeur de message
moko138 a écrit :
1) Les balises-code sont les < > (crochets bleus) de la barre de mise en forme.
_ _ _3) /!\ Si vous avez plusieurs retours à donner, séparez-les bien (toujours pour la lisibilité) :
commecela.
J'ai le msg suivant juste avant l'affichage de la page de connexion:
i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data table pointersmassimo@massimo:~$ sudo dmesg –level=err
[ 5.640912] i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data table pointers[ 25.701055] b43-phy0 ERROR: Firmware file "b43/ucode15.fw" not found
[ 25.701061] b43-phy0 ERROR: Firmware file "b43-open/ucode15.fw" not found
[ 25.701064] b43-phy0 ERROR: You must go to https://wireless.wiki.kernel.org/en/use … cefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website. massimo@massimo:~$ sudo dmesg –level=warn
[ 0.017442] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/64 (20221020/tbfadt-564)
[ 0.359130] pmd_set_huge: Cannot satisfy [mem 0xf8000000-0xf8200000] with a huge-page mapping due to MTRR override.
[ 0.708172] pnp 00:08: disabling [mem 0x000c0000-0x000cffff] because it overlaps 0000:00:02.0 BAR 6 [mem 0x000c0000-0x000dffff]
[ 0.909953] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log.
[ 0.910110] platform eisa.0: EISA: Cannot allocate resource for mainboard
[ 0.910112] platform eisa.0: Cannot allocate resource for EISA slot 1
[ 0.910115] platform eisa.0: Cannot allocate resource for EISA slot 2
[ 0.910117] platform eisa.0: Cannot allocate resource for EISA slot 3
[ 0.910119] platform eisa.0: Cannot allocate resource for EISA slot 4
[ 0.910121] platform eisa.0: Cannot allocate resource for EISA slot 5
[ 0.910124] platform eisa.0: Cannot allocate resource for EISA slot 6
[ 0.910126] platform eisa.0: Cannot allocate resource for EISA slot 7
[ 0.910128] platform eisa.0: Cannot allocate resource for EISA slot 8
[ 2.716326] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[ 2.716330] clocksource: 'hpet' wd_nsec: 500349031 wd_now: 23187a9 wd_last: 1c436f2 mask: ffffffff
[ 2.716333] clocksource: 'tsc' cs_nsec: 479976147 cs_now: 6f80a62ff cs_last: 6b9422302 mask: ffffffffffffffff
[ 2.716336] clocksource: 'tsc' is current clocksource.
[ 2.728283] TSC found unstable after boot, most likely due to broken BIOS. Use 'tsc=unstable'.
[ 2.728395] clocksource: Not enough CPUs to check clocksource 'tsc'.
[ 3.069313] wmi_bus wmi_bus-PNP0C14:00: WQBC data block query control method not found
[ 5.640934] ------------[ cut here ]------------
[ 5.640935] i915 0000:00:02.0: Block 42 min_size is zero
[ 5.640972] WARNING: CPU: 0 PID: 95 at drivers/gpu/drm/i915/display/intel_bios.c:471 init_bdb_block+0x317/0x510 [i915]
[ 5.641337] Modules linked in: i915(+) drm_buddy i2c_algo_bit ttm drm_display_helper cec rc_core drm_kms_helper syscopyarea hid_generic sysfillrect sysimgblt gpio_ich sha512_ssse3 usbhid psmouse hid ums_realtek uas ahci i2c_i801 drm i2c_smbus r8169 libahci lpc_ich usb_storage realtek ssb video wmi
[ 5.641374] CPU: 0 PID: 95 Comm: systemd-udevd Not tainted 6.2.0-31-generic #31~22.04.1-Ubuntu
[ 5.641377] Hardware name: Dell Inc. Vostro 1220 /0X482M, BIOS 1.3.0 10/15/2009
[ 5.641379] RIP: 0010:init_bdb_block+0x317/0x510 [i915]
[ 5.641655] Code: 8b 7b 08 4c 8b 77 50 4d 85 f6 74 29 4c 89 45 d0 e8 ee 33 dd cd 44 89 e1 4c 89 f2 48 c7 c7 68 6a 85 c0 48 89 c6 e8 19 39 40 cd <0f> 0b 4c 8b 45 d0 e9 35 fd ff ff 4c 8b 37 eb d2 4c 89 ee 48 c7 c7
[ 5.641659] RSP: 0018:ffffa6bd80453878 EFLAGS: 00010246
[ 5.641663] RAX: 0000000000000000 RBX: ffff8d25ea968000 RCX: 0000000000000000
[ 5.641665] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 5.641667] RBP: ffffa6bd804538c8 R08: 0000000000000000 R09: 0000000000000000
[ 5.641669] R10: 0000000000000000 R11: 0000000000000000 R12: 000000000000002a
[ 5.641671] R13: 0000000000000000 R14: ffff8d26c0b99f60 R15: 0000000000000000
[ 5.641673] FS: 00007f98c2ae78c0(0000) GS:ffff8d26dbc00000(0000) knlGS:0000000000000000
[ 5.641676] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 5.641679] CR2: 000055c43464d470 CR3: 00000000025de000 CR4: 00000000000406f0
[ 5.641681] Call Trace:
[ 5.641684] <TASK>
[ 5.641688] intel_bios_init+0x160/0x3c0 [i915]
[ 5.641950] ? drm_vblank_init+0x6c/0x140 [drm]
[ 5.642031] intel_modeset_init_noirq+0x3a/0x270 [i915]
[ 5.642293] i915_driver_probe+0x10d/0x430 [i915]
[ 5.642483] ? acpi_dev_found+0x66/0x80
[ 5.642490] i915_pci_probe+0xa8/0x1b0 [i915]
[ 5.642685] local_pci_probe+0x4b/0xb0
[ 5.642689] pci_call_probe+0x55/0x190
[ 5.642693] pci_device_probe+0x84/0x120
[ 5.642698] really_probe+0x1ed/0x450
[ 5.642703] __driver_probe_device+0x8a/0x190
[ 5.642707] driver_probe_device+0x23/0xd0
[ 5.642712] __driver_attach+0x10f/0x220
[ 5.642716] ? __pfx___driver_attach+0x10/0x10
[ 5.642721] bus_for_each_dev+0x83/0xe0
[ 5.642724] driver_attach+0x1e/0x30
[ 5.642728] bus_add_driver+0x152/0x250
[ 5.642733] driver_register+0x83/0x160
[ 5.642736] __pci_register_driver+0x68/0x80
[ 5.642739] i915_pci_register_driver+0x23/0x30 [i915]
[ 5.642933] i915_init+0x37/0x120 [i915]
[ 5.643134] ? __pfx_init_module+0x10/0x10 [i915]
[ 5.643335] do_one_initcall+0x49/0x240
[ 5.643341] ? kmalloc_trace+0x2a/0xb0
[ 5.643346] do_init_module+0x52/0x240
[ 5.643351] load_module+0xb96/0xd60
[ 5.643356] __do_sys_finit_module+0xcc/0x150
[ 5.643360] ? __do_sys_finit_module+0xcc/0x150
[ 5.643365] __x64_sys_finit_module+0x18/0x30
[ 5.643369] do_syscall_64+0x5c/0x90
[ 5.643374] ? do_syscall_64+0x69/0x90
[ 5.643378] ? exit_to_user_mode_prepare+0x3b/0xd0
[ 5.643381] ? syscall_exit_to_user_mode+0x2a/0x50
[ 5.643385] ? do_syscall_64+0x69/0x90
[ 5.643388] ? do_syscall_64+0x69/0x90
[ 5.643391] ? do_syscall_64+0x69/0x90
[ 5.643395] ? do_syscall_64+0x69/0x90
[ 5.643398] ? do_syscall_64+0x69/0x90
[ 5.643401] ? sysvec_apic_timer_interrupt+0x4e/0xb0
[ 5.643404] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 5.643408] RIP: 0033:0x7f98c31dfa3d
[ 5.643413] Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d c3 a3 0f 00 f7 d8 64 89 01 48
[ 5.643415] RSP: 002b:00007ffdf27712f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 5.643420] RAX: ffffffffffffffda RBX: 000055c434605af0 RCX: 00007f98c31dfa3d
[ 5.643422] RDX: 0000000000000000 RSI: 00007f98c3376441 RDI: 0000000000000016
[ 5.643424] RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000002
[ 5.643426] R10: 0000000000000016 R11: 0000000000000246 R12: 00007f98c3376441
[ 5.643429] R13: 000055c434662ef0 R14: 000055c434668c50 R15: 000055c43466ed20
[ 5.643433] </TASK>
[ 5.643434] ---[ end trace 0000000000000000 ]---
[ 22.805314] at24 0-0050: supply vcc not found, using dummy regulator
[ 23.926374] dell-smbios A80593CE-A997-11DA-B012-B622A1EF5492: WMI SMBIOS userspace interface not supported(0), try upgrading to a newer BIOS
[ 25.700905] b43 ssb0:0: Direct firmware load for b43/ucode15.fw failed with error -2
[ 25.700959] b43 ssb0:0: Direct firmware load for b43/ucode15.fw failed with error -2
[ 25.701015] b43 ssb0:0: Direct firmware load for b43-open/ucode15.fw failed with error -2
[ 25.701051] b43 ssb0:0: Direct firmware load for b43-open/ucode15.fw failed with error -2
[ 50.558466] kauditd_printk_skb: 61 callbacks suppressed==============
Montre, en te servant du Retour utilisable de commande :
lspci -vnn | grep -A 12 '\''[030[02]\]' | grep -Ei "vga|3d|display|kernel"uname -adpkg -l | grep -v ^iiet :
echo $XDG_SESSION_TYPEpour voir si c'est Wayland ou x11.
_ _ _
(Edit= messages regroupés)
_ _ _
Lecture conseillée > memento des balises code.
Donne la commande et son retour ensemble.
massimo@massimo:~$ lspci -vnn | grep -A 12 '\''[030[02]\]' | grep -Ei "vga|3d|display|kernel"
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) (prog-if 00 [VGA controller])
Kernel driver in use: i915
Kernel modules: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)uname -a
Linux massimo 6.2.0-31-generic #31~22.04.1-Ubuntu SMP PREEMPT_DYNAMIC Wed Aug 16 13:45:26 UTC 2 x86_64 x86_64 x86_64 GNU/Linuxdpkg -l | grep -v ^ii
Souhait=inconnU/Installé/suppRimé/Purgé/H=à garder
| État=Non/Installé/fichier-Config/dépaqUeté/échec-conFig/H=semi-installé/W=attend-traitement-déclenchements
|/ Err?=(aucune)/besoin Réinstallation (État,Err: majuscule=mauvais)
||/ Nom Version Architecture Description
+++-=============================================-=======================================-============-================================================================================
rc linux-image-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Signed kernel image generic
rc linux-modules-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Linux kernel extra modules for version 5.19.0 on 64 bit x86 SMP
rc linux-modules-extra-5.19.0-32-generic 5.19.0-32.33~22.04.1 amd64 Linux kernel extra modules for version 5.19.0 on 64 bit x86 SMPmassimo@massimo:~$ echo $XDG_SESSION_TYPE
x11Avant le passage de la patrouille :
Dans ses observations, cqfd93 a écrit :
Modération - Balises code à ajouter aux messages comme demandé, ça ne se fera pas tout seul
Dernière modification par xubu1957 (Le 24/01/2024, à 23:53)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#4 Le 24/01/2024, à 23:40
- H_67
Re : msg i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data .....
Bonjour,
Dans la commande : sudo dmesg –level=warn
il y a la ligne : [ 5.640935] i915 0000:00:02.0: Block 42 min_size is zero
Je me pose la question suivante : suis-je dans le même cas de figure que celui relevé sur le site https://gitlab.freedesktop.org/drm/intel/-/issues/6592
où il est fait mention de : Block 42 min_size is zero error during startup
Dans l'affirmative il faudrait remplacé le fichier i915_vbt par celui existant sur le site cité plus haut.
Comment mettre en oeuvre cette solution par un débutant ?
Merci d'avance pour vos réponses
Hors ligne
#5 Le 24/01/2024, à 23:52
- xubu1957
Re : msg i915 0000:00:02.0: [drm] *ERROR* VBT has malformed LFP data .....
Bonjour,
Pour info > bugs.launchpad.net/ubuntu/+source/linux/+bug/1996068 i915 0000:00:02.0: Block 42 min_size is zero | WARNING: CPU: 2 PID: 254 at drivers/gpu/drm/i915/display/intel_bios.c:476 init_bdb_block+0x29a/0x460 [i915]
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne