#1 Le 31/03/2020, à 22:43
- xvi019
Short Self-test : Complited with read failure
Bonsoir a tous ,
je viens de faire une analyse a gsmartcontrol et ça ma mis une erreur " Complited with read failure " , voila l'output de cette analyse :
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-91-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST1000LM035-1RK172
Serial Number: WCB17BGF
LU WWN Device Id: 5 000c50 09c534acd
Firmware Version: SDM1
User Capacity: 1000204886016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Mar 31 21:10:31 2020 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, NOT FROZEN [SEC1]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x79) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 169) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 054 054 006 - 208450474
3 Spin_Up_Time PO---- 099 099 000 - 0
4 Start_Stop_Count -O--CK 088 088 020 - 13168
5 Reallocated_Sector_Ct PO--CK 092 092 036 - 5344
7 Seek_Error_Rate POSR-- 072 060 045 - 86191924528
9 Power_On_Hours -O--CK 097 097 000 - 3448 (112 214 0)
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 098 098 020 - 2864
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 073 073 000 - 27
188 Command_Timeout -O--CK 100 099 000 - 34360262664
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 063 048 040 - 37 (Min/Max 24/37)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 889
192 Power-Off_Retract_Count -O--CK 100 100 000 - 105
193 Load_Cycle_Count -O--CK 086 086 000 - 28496
194 Temperature_Celsius -O---K 037 052 000 - 37 (0 14 0 0 0)
197 Current_Pending_Sector -O--C- 094 090 000 - 512
198 Offline_Uncorrectable ----C- 094 090 000 - 512
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
240 Head_Flying_Hours ------ 100 253 000 - 3377 (173 140 0)
241 Total_LBAs_Written ------ 100 253 000 - 12567110453
242 Total_LBAs_Read ------ 100 253 000 - 20611987758
254 Free_Fall_Sensor -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x24 GPL R/O 512 Current Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 24 Device vendor specific log
0xa2 GPL VS 8160 Device vendor specific log
0xa8 GPL,SL VS 136 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xab GPL VS 1 Device vendor specific log
0xb0 GPL VS 8920 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL,SL VS 16 Device vendor specific log
0xc2 GPL,SL VS 240 Device vendor specific log
0xc3 GPL,SL VS 8 Device vendor specific log
0xc4 GPL,SL VS 24 Device vendor specific log
0xc9 GPL,SL VS 1 Device vendor specific log
0xca GPL,SL VS 16 Device vendor specific log
0xd3 GPL VS 1920 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 27 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 27 [6] occurred at disk power-on lifetime: 3444 hours (143 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6a e2 2a 38 00 00 Error: UNC at LBA = 0x6ae22a38 = 1793206840
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 01 00 00 00 6a e2 29 58 40 00 05:58:06.311 READ FPDMA QUEUED
60 00 00 00 e0 00 00 68 32 ee 98 40 00 05:58:06.298 READ FPDMA QUEUED
60 00 00 00 e0 00 00 69 48 27 00 40 00 05:58:06.263 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 05:58:06.215 FLUSH CACHE EXT
60 00 00 00 e0 00 00 68 7c 89 f8 40 00 05:58:06.185 READ FPDMA QUEUED
Error 26 [5] occurred at disk power-on lifetime: 3420 hours (142 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6a e2 2a 38 00 00 Error: UNC at LBA = 0x6ae22a38 = 1793206840
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 01 00 00 00 6a e2 29 58 40 00 01:14:21.071 READ FPDMA QUEUED
60 00 00 00 e0 00 00 68 32 ee 98 40 00 01:14:21.058 READ FPDMA QUEUED
60 00 00 00 e0 00 00 69 48 27 00 40 00 01:14:21.041 READ FPDMA QUEUED
60 00 00 00 e0 00 00 68 7c 89 f8 40 00 01:14:21.030 READ FPDMA QUEUED
60 00 00 00 e0 00 00 6c 88 68 18 40 00 01:14:21.008 READ FPDMA QUEUED
Error 25 [4] occurred at disk power-on lifetime: 3277 hours (136 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 70 0d 82 10 00 00 Error: UNC at LBA = 0x700d8210 = 1879933456
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 70 0d 82 10 40 00 00:32:49.199 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:32:49.187 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:32:49.161 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:32:49.160 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:32:49.147 SET FEATURES [Set transfer mode]
Error 24 [3] occurred at disk power-on lifetime: 3277 hours (136 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 70 0d 82 10 00 00 Error: UNC at LBA = 0x700d8210 = 1879933456
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 70 0d 82 10 40 00 00:32:49.005 READ FPDMA QUEUED
60 00 00 00 08 00 00 70 0d 82 08 40 00 00:32:49.005 READ FPDMA QUEUED
60 00 00 00 08 00 00 70 0d 82 00 40 00 00:32:49.004 READ FPDMA QUEUED
60 00 00 00 08 00 00 70 0d 81 f8 40 00 00:32:48.984 READ FPDMA QUEUED
60 00 00 00 08 00 00 70 0d 81 f0 40 00 00:32:48.983 READ FPDMA QUEUED
Error 23 [2] occurred at disk power-on lifetime: 3277 hours (136 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 70 0d 82 10 00 00 Error: UNC at LBA = 0x700d8210 = 1879933456
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 01 00 00 00 70 0d 81 20 40 00 00:32:48.333 READ FPDMA QUEUED
60 00 00 01 00 00 00 70 0d 80 20 40 00 00:32:48.321 READ FPDMA QUEUED
60 00 00 01 00 00 00 70 0d 7f 20 40 00 00:32:48.310 READ FPDMA QUEUED
60 00 00 01 00 00 00 70 0d 7e 20 40 00 00:32:48.297 READ FPDMA QUEUED
60 00 00 01 00 00 00 70 0d 7d 20 40 00 00:32:48.283 READ FPDMA QUEUED
Error 22 [1] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 89 08 00 00 Error: UNC at LBA = 0x6e848908 = 1854179592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 89 08 40 00 00:51:55.119 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f ae 38 40 00 00:51:55.119 READ FPDMA QUEUED
60 00 00 00 10 00 00 68 7f ae 00 40 00 00:51:55.117 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:51:55.107 SET FEATURES [Enable SATA feature]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:51:55.098 SET FEATURES [Enable SATA feature]
Error 21 [0] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 89 08 00 00 Error: UNC at LBA = 0x6e848908 = 1854179592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 89 08 40 00 00:51:54.623 READ FPDMA QUEUED
ef 00 10 00 03 00 00 00 00 00 00 a0 00 00:51:54.612 SET FEATURES [Enable SATA feature]
ef 00 10 00 02 00 00 00 00 00 00 a0 00 00:51:54.603 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 00 00:51:54.576 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:51:54.575 IDENTIFY DEVICE
Error 20 [19] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 89 08 00 00 Error: UNC at LBA = 0x6e848908 = 1854179592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 89 08 40 00 00:51:54.100 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 c0 40 00 00:51:54.080 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 90 40 00 00:51:54.065 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 20 40 00 00:51:54.064 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 48 40 00 00:51:54.064 READ FPDMA QUEUED
Error 19 [18] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 89 98 00 00 Error: UNC at LBA = 0x6e848998 = 1854179736
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 68 7f a3 90 40 00 00:51:53.517 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 58 40 00 00:51:53.517 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 48 40 00 00:51:53.517 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f a3 20 40 00 00:51:53.517 READ FPDMA QUEUED
60 00 00 00 80 00 00 6e 84 89 48 40 00 00:51:53.514 READ FPDMA QUEUED
Error 18 [17] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 89 08 00 00 Error: UNC at LBA = 0x6e848908 = 1854179592
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 80 00 00 6e 84 89 48 40 00 00:51:53.008 READ FPDMA QUEUED
60 00 00 00 40 00 00 6e 84 89 08 40 00 00:51:53.004 READ FPDMA QUEUED
60 00 00 00 20 00 00 6e 84 88 e8 40 00 00:51:52.991 READ FPDMA QUEUED
60 00 00 00 08 00 00 6e 84 8a 50 40 00 00:51:52.982 READ FPDMA QUEUED
60 00 00 00 08 00 00 6e 84 8b f0 40 00 00:51:52.967 READ FPDMA QUEUED
Error 17 [16] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 84 a8 00 00 Error: UNC at LBA = 0x6e8484a8 = 1854178472
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 84 a8 40 00 00:51:52.050 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f b3 d0 40 00 00:51:52.031 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f b3 b0 40 00 00:51:52.031 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f b3 a0 40 00 00:51:52.031 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 7f b3 68 40 00 00:51:52.031 READ FPDMA QUEUED
Error 16 [15] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 84 a8 00 00 Error: UNC at LBA = 0x6e8484a8 = 1854178472
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 84 a8 40 00 00:51:51.476 READ FPDMA QUEUED
60 00 00 00 08 00 00 6e 84 84 a0 40 00 00:51:51.474 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 00:51:51.458 FLUSH CACHE EXT
60 00 00 00 08 00 00 6e 84 84 98 40 00 00:51:51.457 READ FPDMA QUEUED
61 00 00 00 08 00 00 6a fa 63 b0 40 00 00:51:51.457 WRITE FPDMA QUEUED
Error 15 [14] occurred at disk power-on lifetime: 2983 hours (124 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6e 84 84 a8 00 00 Error: UNC at LBA = 0x6e8484a8 = 1854178472
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 6e 84 84 f0 40 00 00:51:50.736 READ FPDMA QUEUED
60 00 00 00 70 00 00 6e 84 84 78 40 00 00:51:50.734 READ FPDMA QUEUED
60 00 00 01 00 00 00 6e 84 83 78 40 00 00:51:50.692 READ FPDMA QUEUED
60 00 00 00 c8 00 00 6e 84 82 78 40 00 00:51:50.675 READ FPDMA QUEUED
60 00 00 00 28 00 00 6e 84 83 50 40 00 00:51:50.674 READ FPDMA QUEUED
Error 14 [13] occurred at disk power-on lifetime: 2892 hours (120 days + 12 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 89 f5 98 00 00 Error: UNC at LBA = 0x6889f598 = 1753871768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 40 00 00 68 89 f4 d8 40 00 00:07:18.560 READ FPDMA QUEUED
60 00 00 00 48 00 00 68 89 f5 38 40 00 00:07:18.559 READ FPDMA QUEUED
60 00 00 00 50 00 00 68 89 f5 88 40 00 00:07:18.557 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 8a 27 f0 40 00 00:07:18.337 READ FPDMA QUEUED
60 00 00 00 a0 00 00 68 8a 27 00 40 00 00:07:18.335 READ FPDMA QUEUED
Error 13 [12] occurred at disk power-on lifetime: 2887 hours (120 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 89 f5 98 00 00 Error: UNC at LBA = 0x6889f598 = 1753871768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 e8 00 00 68 89 f5 18 40 00 00:14:45.562 READ FPDMA QUEUED
60 00 00 01 00 00 00 69 5b 34 c0 40 00 00:14:45.442 READ FPDMA QUEUED
60 00 00 00 80 00 00 68 88 78 48 40 00 00:14:45.313 READ FPDMA QUEUED
60 00 00 00 48 00 00 69 5b 5f b0 40 00 00:14:45.298 READ FPDMA QUEUED
60 00 00 00 c8 00 00 68 8a 1d d8 40 00 00:14:45.285 READ FPDMA QUEUED
Error 12 [11] occurred at disk power-on lifetime: 2634 hours (109 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 6a e1 f5 78 00 00 Error: UNC at LBA = 0x6ae1f578 = 1793193336
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 10 00 00 6a e1 f5 c0 40 00 00:27:24.824 READ FPDMA QUEUED
60 00 00 00 08 00 00 6a e1 f5 b0 40 00 00:27:24.824 READ FPDMA QUEUED
60 00 00 00 08 00 00 6a e1 f5 98 40 00 00:27:24.824 READ FPDMA QUEUED
60 00 00 00 10 00 00 6a e1 f5 70 40 00 00:27:24.824 READ FPDMA QUEUED
60 00 00 00 08 00 00 6a e1 f5 58 40 00 00:27:24.824 READ FPDMA QUEUED
Error 11 [10] occurred at disk power-on lifetime: 2590 hours (107 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 70 43 90 00 00 Error: WP at LBA = 0x68704390 = 1752187792
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 00 6e 36 28 c8 40 00 00:48:29.407 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 70 49 dd c8 40 00 00:48:29.407 WRITE FPDMA QUEUED
60 00 00 00 08 00 00 68 70 43 90 40 00 00:48:29.406 READ FPDMA QUEUED
61 00 00 00 38 00 00 71 36 ff 30 40 00 00:48:29.406 WRITE FPDMA QUEUED
61 00 00 00 c0 00 00 6a f5 1a b8 40 00 00:48:29.406 WRITE FPDMA QUEUED
Error 10 [9] occurred at disk power-on lifetime: 2590 hours (107 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 70 43 70 00 00 Error: WP at LBA = 0x68704370 = 1752187760
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 10 00 00 6e 36 28 b0 40 00 00:48:27.531 WRITE FPDMA QUEUED
60 00 00 00 38 00 00 68 70 43 c8 40 00 00:48:27.531 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 70 43 b8 40 00 00:48:27.499 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 70 43 a0 40 00 00:48:27.499 READ FPDMA QUEUED
60 00 00 00 40 00 00 68 70 43 58 40 00 00:48:27.499 READ FPDMA QUEUED
Error 9 [8] occurred at disk power-on lifetime: 2589 hours (107 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 70 44 98 00 00 Error: UNC at LBA = 0x68704498 = 1752188056
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 20 00 00 68 4f 93 00 40 00 09:51:59.872 READ FPDMA QUEUED
60 00 00 00 48 00 00 68 70 44 80 40 00 09:51:59.870 READ FPDMA QUEUED
60 00 00 00 10 00 00 68 70 44 58 40 00 09:51:59.867 READ FPDMA QUEUED
60 00 00 00 10 00 00 68 70 44 40 40 00 09:51:59.867 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 70 44 10 40 00 09:51:59.867 READ FPDMA QUEUED
Error 8 [7] occurred at disk power-on lifetime: 2588 hours (107 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 00 68 70 43 78 00 00 Error: UNC at LBA = 0x68704378 = 1752187768
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 68 55 a1 a0 40 00 08:38:18.309 READ FPDMA QUEUED
60 00 00 00 20 00 00 68 55 a1 48 40 00 08:38:18.309 READ FPDMA QUEUED
60 00 00 00 18 00 00 68 55 a1 18 40 00 08:38:18.309 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 55 a0 f0 40 00 08:38:18.309 READ FPDMA QUEUED
60 00 00 00 08 00 00 68 55 a0 d0 40 00 08:38:18.309 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 3448 1793206840
# 2 Short offline Completed: read failure 90% 3448 1793206840
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 37 Celsius
Power Cycle Min/Max Temperature: 24/37 Celsius
Lifetime Min/Max Temperature: 14/52 Celsius
Lifetime Average Temperature: 36 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 30 minutes
Min/Max recommended Temperature: 14/55 Celsius
Min/Max Temperature Limit: 10/60 Celsius
Temperature History Size (Index): 128 (39)
Index Estimated Time Temperature Celsius
40 2020-03-29 05:30 34 ***************
41 2020-03-29 06:00 38 *******************
42 2020-03-29 06:30 38 *******************
43 2020-03-29 07:00 38 *******************
44 2020-03-29 07:30 39 ********************
... ..( 2 skipped). .. ********************
47 2020-03-29 09:00 39 ********************
48 2020-03-29 09:30 38 *******************
49 2020-03-29 10:00 39 ********************
50 2020-03-29 10:30 39 ********************
51 2020-03-29 11:00 38 *******************
52 2020-03-29 11:30 36 *****************
53 2020-03-29 12:00 36 *****************
54 2020-03-29 12:30 36 *****************
55 2020-03-29 13:00 35 ****************
... ..( 4 skipped). .. ****************
60 2020-03-29 15:30 35 ****************
61 2020-03-29 16:00 36 *****************
62 2020-03-29 16:30 35 ****************
... ..( 5 skipped). .. ****************
68 2020-03-29 19:30 35 ****************
69 2020-03-29 20:00 36 *****************
70 2020-03-29 20:30 36 *****************
71 2020-03-29 21:00 35 ****************
72 2020-03-29 21:30 35 ****************
73 2020-03-29 22:00 35 ****************
74 2020-03-29 22:30 ? -
75 2020-03-29 23:00 29 **********
76 2020-03-29 23:30 ? -
77 2020-03-30 00:00 24 *****
78 2020-03-30 00:30 34 ***************
79 2020-03-30 01:00 32 *************
80 2020-03-30 01:30 33 **************
81 2020-03-30 02:00 37 ******************
82 2020-03-30 02:30 38 *******************
83 2020-03-30 03:00 39 ********************
84 2020-03-30 03:30 40 *********************
85 2020-03-30 04:00 38 *******************
86 2020-03-30 04:30 36 *****************
87 2020-03-30 05:00 38 *******************
88 2020-03-30 05:30 41 **********************
89 2020-03-30 06:00 39 ********************
90 2020-03-30 06:30 40 *********************
91 2020-03-30 07:00 39 ********************
92 2020-03-30 07:30 36 *****************
93 2020-03-30 08:00 36 *****************
94 2020-03-30 08:30 36 *****************
95 2020-03-30 09:00 35 ****************
96 2020-03-30 09:30 38 *******************
97 2020-03-30 10:00 36 *****************
98 2020-03-30 10:30 35 ****************
99 2020-03-30 11:00 35 ****************
100 2020-03-30 11:30 35 ****************
101 2020-03-30 12:00 ? -
102 2020-03-30 12:30 18 -
103 2020-03-30 13:00 31 ************
104 2020-03-30 13:30 32 *************
105 2020-03-30 14:00 34 ***************
106 2020-03-30 14:30 32 *************
107 2020-03-30 15:00 34 ***************
108 2020-03-30 15:30 36 *****************
109 2020-03-30 16:00 36 *****************
110 2020-03-30 16:30 ? -
111 2020-03-30 17:00 21 **
112 2020-03-30 17:30 35 ****************
113 2020-03-30 18:00 32 *************
114 2020-03-30 18:30 32 *************
115 2020-03-30 19:00 32 *************
116 2020-03-30 19:30 36 *****************
117 2020-03-30 20:00 37 ******************
118 2020-03-30 20:30 38 *******************
119 2020-03-30 21:00 32 *************
120 2020-03-30 21:30 32 *************
121 2020-03-30 22:00 32 *************
122 2020-03-30 22:30 37 ******************
123 2020-03-30 23:00 36 *****************
124 2020-03-30 23:30 36 *****************
125 2020-03-31 00:00 38 *******************
126 2020-03-31 00:30 35 ****************
127 2020-03-31 01:00 ? -
0 2020-03-31 01:30 28 *********
1 2020-03-31 02:00 35 ****************
2 2020-03-31 02:30 37 ******************
3 2020-03-31 03:00 39 ********************
4 2020-03-31 03:30 37 ******************
5 2020-03-31 04:00 36 *****************
6 2020-03-31 04:30 37 ******************
7 2020-03-31 05:00 ? -
8 2020-03-31 05:30 27 ********
9 2020-03-31 06:00 38 *******************
10 2020-03-31 06:30 39 ********************
11 2020-03-31 07:00 39 ********************
12 2020-03-31 07:30 38 *******************
13 2020-03-31 08:00 40 *********************
14 2020-03-31 08:30 40 *********************
15 2020-03-31 09:00 38 *******************
16 2020-03-31 09:30 ? -
17 2020-03-31 10:00 19 -
18 2020-03-31 10:30 33 **************
19 2020-03-31 11:00 33 **************
20 2020-03-31 11:30 33 **************
21 2020-03-31 12:00 36 *****************
22 2020-03-31 12:30 39 ********************
23 2020-03-31 13:00 39 ********************
24 2020-03-31 13:30 39 ********************
25 2020-03-31 14:00 38 *******************
26 2020-03-31 14:30 33 **************
27 2020-03-31 15:00 33 **************
28 2020-03-31 15:30 33 **************
29 2020-03-31 16:00 38 *******************
30 2020-03-31 16:30 39 ********************
31 2020-03-31 17:00 38 *******************
32 2020-03-31 17:30 39 ********************
33 2020-03-31 18:00 38 *******************
34 2020-03-31 18:30 39 ********************
35 2020-03-31 19:00 39 ********************
36 2020-03-31 19:30 ? -
37 2020-03-31 20:00 24 *****
38 2020-03-31 20:30 34 ***************
39 2020-03-31 21:00 37 ******************
SCT Error Recovery Control command not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 2864 --- Lifetime Power-On Resets
0x01 0x010 4 3448 --- Power-on Hours
0x01 0x018 6 12574409257 --- Logical Sectors Written
0x01 0x020 6 209645045 --- Number of Write Commands
0x01 0x028 6 20619003791 --- Logical Sectors Read
0x01 0x030 6 304348107 --- Number of Read Commands
0x01 0x038 6 - --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 454 --- Spindle Motor Power-on Hours
0x03 0x010 4 395 --- Head Flying Hours
0x03 0x018 4 28496 --- Head Load Events
0x03 0x020 4 5344 --- Number of Reallocated Logical Sectors
0x03 0x028 4 738 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 512 --- Number of Realloc. Candidate Logical Sectors
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 1370 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 8 --- Resets Between Cmd Acceptance and Completion
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FISDu coup je sais pas si vous pouvez m'aider a resoudre ce probleme ,j'espere en tout cas que ce n'est pas trop grave .
Merci a vous
Hors ligne
#2 Le 01/04/2020, à 09:01
- moko138
Re : Short Self-test : Complited with read failure
197 Current_Pending_Sector - 512 198 Offline_Uncorrectable - 512
Tu as gagné un presse-papier de 10 x 6,3 cm.
« Fermez le ban »
Et si tu veux que ton prochain disque rotatif dure plus longtemps,
1) évite-lui les secousses en fonction :
191 G-Sense_Error_Rate - 8892) Évite aussi de lui bloquer les parcages :
APM level is: 254 (maximum performance)Explications là : Parcages et température des disques rotatifs : compromis [tutoriel]
(Même si pour ce disque-là, il semble que ça n'ait pas été un problème :
190 Airflow_Temperature_Cel - 37 (Min/Max 24/37)
Dernière modification par moko138 (Le 01/04/2020, à 09:04)
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#3 Le 01/04/2020, à 09:14
- xvi019
Re : Short Self-test : Complited with read failure
@moko138 qaund tu dis que j'ai gagné un presse papier , c'est a dire que la mon disque dur est mort ?
et si il y'a encore un espoire est-ce qu'il y a une methode a suivre pour pouvoir regler ça ou au moin limiter la casse ?
Dernière modification par xvi019 (Le 01/04/2020, à 09:20)
Hors ligne
#4 Le 01/04/2020, à 10:06
- moko138
Re : Short Self-test : Complited with read failure
Ce disque n'est pas mort mais trop dégradé pour être utilisable.
Pour imiter la casse,
- l'option rapide est de sauvegarder ce qui ne l'a pas déjà été, avant de mettre le HDD au rebut.
ATTENTION, pendant tes sauvegardes, à ne pas écraser un fichier sain par sa version illisible !
- Une autre option, plus lente, si tu as un autre HDD sous la main et au moins aussi grand, et sain,
est de faire une image-disque avec gddrescue.
Mais pour ça, il faut du temps et un autre disque disponible, et je ne pourrai pas t'aider.
Est-ce que ce disque a chuté (ou pris un gros choc du même ordre) pendant qu'il tournait ?
%NOINDEX%
Un utilitaire précieux : ncdu
Photo, mini-tutoriel : À la découverte de dcraw
Hors ligne
#5 Le 01/04/2020, à 10:11
- xvi019
Re : Short Self-test : Complited with read failure
non pas que je m'en souvienne , mais apres tout c'est tout a fait probable
et comment differencier un fichier sain d'un fichier illisible ?
j'ai une autre demande a te faire , as-tu des liens interresent vers des sites ou autres discussion dans le forum ,sur ce genre de probleme ,afin d'eviter a l'avenir que ça se reproduise ?
Hors ligne