#26 Le 04/03/2024, à 20:45
- AleksJ
Re : Connexion Wifi Starlink
Alors je viens de faire un nettoyage des connexions etc
Voici le résultat :
~$ nmcli c s "RouteurStarlink5ghz" |cat
connection.id: RouteurStarlink5ghz
connection.uuid: c368c280-f261-4580-a764-caeb720258e1
connection.stable-id: --
connection.type: 802-11-wireless
connection.interface-name: wlp3s0
connection.autoconnect: oui
connection.autoconnect-priority: 0
connection.autoconnect-retries: -1 (default)
connection.multi-connect: 0 (default)
connection.auth-retries: -1
connection.timestamp: 0
connection.read-only: non
connection.permissions: --
connection.zone: --
connection.master: --
connection.slave-type: --
connection.autoconnect-slaves: -1 (default)
connection.secondaries: --
connection.gateway-ping-timeout: 0
connection.metered: inconnu
connection.lldp: default
connection.mdns: -1 (default)
connection.llmnr: -1 (default)
connection.dns-over-tls: -1 (default)
connection.wait-device-timeout: -1
802-11-wireless.ssid: RouteurStarlink5ghz
802-11-wireless.mode: infrastructure
802-11-wireless.band: --
802-11-wireless.channel: 0
802-11-wireless.bssid: --
802-11-wireless.rate: 0
802-11-wireless.tx-power: 0
802-11-wireless.mac-address: --
802-11-wireless.cloned-mac-address: --
802-11-wireless.generate-mac-address-mask:--
802-11-wireless.mac-address-blacklist: --
802-11-wireless.mac-address-randomization:default
802-11-wireless.mtu: auto
802-11-wireless.seen-bssids: --
802-11-wireless.hidden: non
802-11-wireless.powersave: 0 (default)
802-11-wireless.wake-on-wlan: 0x1 (default)
802-11-wireless.ap-isolation: -1 (default)
802-11-wireless-security.key-mgmt: wpa-psk
802-11-wireless-security.wep-tx-keyidx: 0
802-11-wireless-security.auth-alg: open
802-11-wireless-security.proto: --
802-11-wireless-security.pairwise: --
802-11-wireless-security.group: --
802-11-wireless-security.pmf: 0 (default)
802-11-wireless-security.leap-username: --
802-11-wireless-security.wep-key0: <hidden>
802-11-wireless-security.wep-key1: <hidden>
802-11-wireless-security.wep-key2: <hidden>
802-11-wireless-security.wep-key3: <hidden>
802-11-wireless-security.wep-key-flags: 0 (aucun)
802-11-wireless-security.wep-key-type: unknown
802-11-wireless-security.psk: <hidden>
802-11-wireless-security.psk-flags: 0 (aucun)
802-11-wireless-security.leap-password: <hidden>
802-11-wireless-security.leap-password-flags:0 (aucun)
802-11-wireless-security.wps-method: 0x0 (default)
802-11-wireless-security.fils: 0 (default)
ipv4.method: auto
ipv4.dns: --
ipv4.dns-search: --
ipv4.dns-options: --
ipv4.dns-priority: 0
ipv4.addresses: --
ipv4.gateway: --
ipv4.routes: --
ipv4.route-metric: -1
ipv4.route-table: 0 (unspec)
ipv4.routing-rules: --
ipv4.ignore-auto-routes: non
ipv4.ignore-auto-dns: non
ipv4.dhcp-client-id: --
ipv4.dhcp-iaid: --
ipv4.dhcp-timeout: 0 (default)
ipv4.dhcp-send-hostname: oui
ipv4.dhcp-hostname: --
ipv4.dhcp-fqdn: --
ipv4.dhcp-hostname-flags: 0x0 (none)
ipv4.never-default: non
ipv4.may-fail: oui
ipv4.required-timeout: -1 (default)
ipv4.dad-timeout: -1 (default)
ipv4.dhcp-vendor-class-identifier: --
ipv4.dhcp-reject-servers: --
ipv6.method: auto
ipv6.dns: --
ipv6.dns-search: --
ipv6.dns-options: --
ipv6.dns-priority: 0
ipv6.addresses: --
ipv6.gateway: --
ipv6.routes: --
ipv6.route-metric: -1
ipv6.route-table: 0 (unspec)
ipv6.routing-rules: --
ipv6.ignore-auto-routes: non
ipv6.ignore-auto-dns: non
ipv6.never-default: non
ipv6.may-fail: oui
ipv6.required-timeout: -1 (default)
ipv6.ip6-privacy: -1 (unknown)
ipv6.addr-gen-mode: stable-privacy
ipv6.ra-timeout: 0 (default)
ipv6.dhcp-duid: --
ipv6.dhcp-iaid: --
ipv6.dhcp-timeout: 0 (default)
ipv6.dhcp-send-hostname: oui
ipv6.dhcp-hostname: --
ipv6.dhcp-hostname-flags: 0x0 (none)
ipv6.token: --
proxy.method: none
proxy.browser-only: non
proxy.pac-url: --
proxy.pac-script: --
GENERAL.NAME: RouteurStarlink5ghz
GENERAL.UUID: c368c280-f261-4580-a764-caeb720258e1
GENERAL.DEVICES: wlp3s0
GENERAL.IP-IFACE: --
GENERAL.STATE: activation
GENERAL.DEFAULT: non
GENERAL.DEFAULT6: non
GENERAL.SPEC-OBJECT: /org/freedesktop/NetworkManager/AccessPoint/251
GENERAL.VPN: non
GENERAL.DBUS-PATH: /org/freedesktop/NetworkManager/ActiveConnection/31
GENERAL.CON-PATH: /org/freedesktop/NetworkManager/Settings/10
GENERAL.ZONE: --
GENERAL.MASTER-PATH: --Hors ligne
#27 Le 05/03/2024, à 10:23
- AleksJ
Re : Connexion Wifi Starlink
Ce matin test avec plusieurs distributions et la gagnante est Kali!
Connexion sans le moindre problème lors de l’installation et stable par la suite.
Dernière modification par AleksJ (Le 05/03/2024, à 10:24)
Hors ligne
#28 Le 05/03/2024, à 10:25
- xubu1957
Re : Connexion Wifi Starlink
Bonjour,
Tu peux montrer :
iwconfignmcli dev wifi | cat?
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Réso|u] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
En ligne
#29 Le 05/03/2024, à 11:51
- AleksJ
Re : Connexion Wifi Starlink
Juste envie de me tirer une balle !
Après redémarrage et fin de l’installation Kali ne veut plus connecter !
J’ai réessayé avec VirtualBox et live USB et c’est pareil.
J’attends le dongle wifi TP-Link ce jour et je croise les doigts en attendant de trouver la solution
Sinon quand je regarde
nmcli device showJ'ai deux fois ma carte Wifi wlp3s0
Est-ce normal ?
~$ nmcli device show
GENERAL.DEVICE: wlp3s0
GENERAL.TYPE: wifi
GENERAL.HWADDR: 14:AC:60:25:60:67
GENERAL.MTU: 1500
GENERAL.STATE: 30 (déconnecté)
GENERAL.CONNECTION: --
GENERAL.CON-PATH: --
IP4.GATEWAY: --
IP6.GATEWAY: --
GENERAL.DEVICE: p2p-dev-wlp3s0
GENERAL.TYPE: wifi-p2p
GENERAL.HWADDR: (inconnu)
GENERAL.MTU: 0
GENERAL.STATE: 30 (déconnecté)
GENERAL.CONNECTION: --
GENERAL.CON-PATH: --
GENERAL.DEVICE: enp2s0
GENERAL.TYPE: ethernet
GENERAL.HWADDR: 74:5D:22:89:4E:3F
GENERAL.MTU: 1500
GENERAL.STATE: 20 (indisponible)
GENERAL.CONNECTION: --
GENERAL.CON-PATH: --
WIRED-PROPERTIES.CARRIER: arrêt
IP4.GATEWAY: --
IP6.GATEWAY: --
GENERAL.DEVICE: lo
GENERAL.TYPE: loopback
GENERAL.HWADDR: 00:00:00:00:00:00
GENERAL.MTU: 65536
GENERAL.STATE: 10 (non-géré)
GENERAL.CONNECTION: --
GENERAL.CON-PATH: --
IP4.ADDRESS[1]: 127.0.0.1/8
IP4.GATEWAY: --
IP6.ADDRESS[1]: ::1/128
IP6.GATEWAY: --
IP6.ROUTE[1]: dst = ::1/128, nh = ::, mt = 256Dernière modification par AleksJ (Le 05/03/2024, à 11:52)
Hors ligne
#30 Le 05/03/2024, à 12:09
- Astrolivier
Re : Connexion Wifi Starlink
Est-ce normal ?
oui, c'est la fonction p2p (une autre manière de faire du wifi dans la norme 802.11), c'est désactivé par défaut
si kali en live usb marche, ce que tu peux faire c'est lancer mon petit script pour le wifi qui donnera plein d'info, ça permettra de voir une bonne partie de la config qui marche
https://github.com/olivierPrigent/wifiCheck/tree/main
wget -N -t 5 -T 10 https://raw.githubusercontent.com/olivierPrigent/wifiCheck/main/wificheck.sh && chmod 755 wificheck.sh && ./wificheck.sh -vtu pourras tout copier direct dans le forum
éventuellement rajouter
nmcli c s "nomDeConnexion"qui n'est pas dans le script
le script est juste une pêche au infos, il ne change rien à ta config, il mettra un fichier wificheck.log dans ton home (mais sur un live cd c'est éphémère)
et moi ça me permet de tester le script ailleurs pour essayer de l'améliorer voir les bugs etc... (aucune obligation évidement, la liste des commande est sur github)
S'il faut absolument faire des sacrifices pour assurer le progrès de l'humanité, ne serait-il pas indispensable de s'en tenir au principe selon lequel c'est à ceux dont on exige le sacrifice que la décision doit revenir en dernier ressort ? (howard zinn)
Hors ligne
#31 Le 05/03/2024, à 12:54
- AleksJ
Re : Connexion Wifi Starlink
Bonjour,
xubu1957 a écrit :
Bonjour,
Tu peux montrer :
iwconfignmcli dev wifi | cat?
Voici les résultats pour
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11 ESSID:"RouteurStarlink5ghz"
Mode:Managed Frequency:2.462 GHz Access Point: 3E:B3:01:2D:11:AA
Bit Rate=115.6 Mb/s Tx-Power=3 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:on
Link Quality=50/70 Signal level=-60 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0$ nmcli dev wifi | cat
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
* 3E:B3:01:2D:11:AA RouteurStarlink5ghz Infra 11 195 Mbit/s 60 ▂▄▆_ WPA2
3E:B3:01:6D:11:AA -- Infra 11 195 Mbit/s 60 ▂▄▆_ WPA2
3E:B3:01:4D:11:AA -- Infra 11 195 Mbit/s 60 ▂▄▆_ WPA2
3E:B3:01:3D:11:AA RouteurStarlink5ghz Infra 36 405 Mbit/s 39 ▂▄__ WPA2
3E:B3:01:5D:11:AA -- Infra 36 405 Mbit/s 37 ▂▄__ WPA2 Hors ligne
#32 Le 05/03/2024, à 12:57
- AleksJ
Re : Connexion Wifi Starlink
Astrolivier a écrit :
Est-ce normal ?
oui, c'est la fonction p2p (une autre manière de faire du wifi dans la norme 802.11), c'est désactivé par défaut
si kali en live usb marche, ce que tu peux faire c'est lancer mon petit script pour le wifi qui donnera plein d'info, ça permettra de voir une bonne partie de la config qui marche
https://github.com/olivierPrigent/wifiCheck/tree/main
wget -N -t 5 -T 10 https://raw.githubusercontent.com/olivierPrigent/wifiCheck/main/wificheck.sh && chmod 755 wificheck.sh && ./wificheck.sh -vtu pourras tout copier direct dans le forum
éventuellement rajouter
nmcli c s "nomDeConnexion"qui n'est pas dans le script
le script est juste une pêche au infos, il ne change rien à ta config, il mettra un fichier wificheck.log dans ton home (mais sur un live cd c'est éphémère)et moi ça me permet de tester le script ailleurs pour essayer de l'améliorer voir les bugs etc... (aucune obligation évidement, la liste des commande est sur github)
Merci 
Voici
###############################################
########### Wifi Check ##################
########### 2024-03-05 ##################
###############################################
##### Current kernel, release, desktop ######
Current Kernel : 6.6.9-amd64
Release Description: Kali GNU/Linux Rolling
Current Desktop : XFCE
################ nmcli #################
wlan0: connected to RouteurStarlink5ghz
"MEDIATEK MT7921 802.11ax"
wifi (mt7921e), 14:AC:60:25:60:67, hw, mtu 1500
ip4 default, ip6 default
inet4 192.168.1.25/24
route4 192.168.1.0/24 metric 600
route4 default via 192.168.1.1 metric 600
inet6 fdb3:1dd:11aa:10::7bd/128
inet6 2a0d:3344:2343:1110::7bd/128
inet6 2a0d:3344:2343:1110:19a:871f:a973:eddc/64
inet6 fdb3:1dd:11aa:10:6c61:c7c5:a215:d392/64
inet6 fe80::1bce:647e:ad3b:5493/64
route6 fe80::/64 metric 1024
route6 fdb3:1dd:11aa:10::/64 metric 600
route6 2a0d:3344:2343:1110::/64 metric 600
route6 fdb3:1dd:11aa::/48 via fe80::7624:9fff:fec2:5d20 metric 600
route6 2a0d:3344:2343:1100::/56 via fe80::7624:9fff:fec2:5d20 metric 600
route6 default via fe80::7624:9fff:fec2:5d20 metric 600
route6 fdb3:1dd:11aa:10::7bd/128 metric 600
route6 2a0d:3344:2343:1110::7bd/128 metric 600
lo: connected (externally) to lo
"lo"
loopback (unknown), 00:00:00:00:00:00, sw, mtu 65536
inet4 127.0.0.1/8
inet6 ::1/128
p2p-dev-wlan0: disconnected
"p2p-dev-wlan0"
wifi-p2p, hw
eth0: unavailable
"Realtek RTL8111/8168/8411"
ethernet (r8169), 74:5D:22:89:4E:3F, hw, mtu 1500
DNS configuration:
servers: 192.168.1.1
domains: lan
interface: wlan0
servers: fdb3:1dd:11aa:10::1
interface: wlan0
Use "nmcli device show" to get complete information about known devices and
############## iw dev ####################
phy#0
Interface wlan0
ifindex 3
wdev 0x1
addr 14:ac:60:25:60:67
ssid RouteurStarlink5ghz
type managed
channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz
txpower 3.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
########### nmcli dev wifi ##############
IN-USE BSSID SSID MODE CHAN RATE SIGNAL BARS SECURITY
3E:B3:01:6D:11:AA -- Infra 11 195 Mbit/s 60 ▂▄▆_ WPA2
3E:B3:01:4D:11:AA -- Infra 11 195 Mbit/s 60 ▂▄▆_ WPA2
* 3E:B3:01:2D:11:AA RouteurStarlink5ghz Infra 11 195 Mbit/s 42 ▂▄__ WPA2
3E:B3:01:3D:11:AA RouteurStarlink5ghz Infra 36 405 Mbit/s 39 ▂▄__ WPA2
3E:B3:01:5D:11:AA -- Infra 36 405 Mbit/s 37 ▂▄__ WPA2
################ lsusb ################
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04f2:b7b4 Chicony Electronics Co., Ltd Integrated Camera
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 04f3:0c4b Elan Microelectronics Corp. ELAN:Fingerprint
Bus 003 Device 003: ID 0489:e0cd Foxconn / Hon Hai MediaTek Bluetooth Adapter
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 002: ID 0781:5583 SanDisk Corp. Ultra Fit
####### lspci -k -nn | grep -A 3 -i net ######
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 15)
Subsystem: Lenovo RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [17aa:50d5]
Kernel driver in use: r8169
Kernel modules: r8169
03:00.0 Network controller [0280]: MEDIATEK Corp. MT7921 802.11ax PCI Express Wireless Network Adapter [14c3:7961]
Subsystem: Lenovo MT7921 802.11ax PCI Express Wireless Network Adapter [17aa:e0bc]
Kernel driver in use: mt7921e
Kernel modules: mt7921e
04:00.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Barcelo [1002:15e7] (rev c5)
####### lsmod | grep <wifi_modules> #######
Module Size Used by
amdgpu 11554816 11
amdxcp 12288 1 amdgpu
bluetooth 1134592 6 btrtl,btmtk,btintel,btbcm,btusb
btbcm 24576 1 btusb
btintel 57344 1 btusb
btmtk 16384 1 btusb
btrtl 32768 1 btusb
btusb 86016 0
cfg80211 1343488 4 mt76,mac80211,mt7921_common,mt76_connac_lib
drm_buddy 20480 1 amdgpu
drm_display_helper 233472 1 amdgpu
drm_exec 16384 1 amdgpu
drm_kms_helper 270336 5 vmwgfx,drm_display_helper,amdgpu
drm_suballoc_helper 12288 1 amdgpu
drm_ttm_helper 12288 2 vmwgfx,amdgpu
gpu_sched 57344 1 amdgpu
hid_generic 12288 0
hid_multitouch 32768 0
i2c_hid 40960 1 i2c_hid_acpi
i2c_hid_acpi 12288 0
mac80211 1392640 4 mt792x_lib,mt76,mt7921_common,mt76_connac_lib
mt76 131072 4 mt792x_lib,mt7921e,mt7921_common,mt76_connac_lib
mt76_connac_lib 98304 3 mt792x_lib,mt7921e,mt7921_common
mt7921_common 86016 1 mt7921e
mt7921e 24576 0
mt792x_lib 69632 2 mt7921e,mt7921_common
snd 155648 45 snd_ctl_led,snd_hda_codec_generic,snd_seq,snd_hda_codec_conexant,snd_seq_device,snd_hda_codec_hdmi,snd_hwdep,snd_hda_intel,snd_hda_codec,snd_sof,snd_timer,snd_compress,thinkpad_acpi,snd_soc_core,snd_pcm
snd_acp3x_pdm_dma 12288 1
snd_acp3x_rn 12288 4
snd_acp_config 16384 5 snd_rn_pci_acp3x,snd_pci_acp6x,snd_pci_acp5x,snd_sof_amd_rembrandt,snd_pci_ps
snd_compress 28672 1 snd_soc_core
snd_ctl_led 24576 0
snd_hda_codec 225280 4 snd_hda_codec_generic,snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel
snd_hda_codec_conexant 32768 1
snd_hda_codec_generic 114688 1 snd_hda_codec_conexant
snd_hda_codec_hdmi 90112 1
snd_hda_core 147456 5 snd_hda_codec_generic,snd_hda_codec_conexant,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_hda_intel 61440 10
snd_hrtimer 12288 1
snd_hwdep 20480 1 snd_hda_codec
snd_pci_acp5x 16384 0
snd_pci_acp6x 16384 0
snd_pci_ps 24576 0
snd_pcm 192512 13 snd_sof_amd_acp,snd_hda_codec_hdmi,snd_pci_acp6x,snd_hda_intel,snd_hda_codec,snd_sof,snd_compress,snd_soc_core,snd_sof_utils,snd_hda_core,snd_acp3x_pdm_dma,snd_pci_ps,snd_pcm_dmaengine
snd_pcm_dmaengine 16384 1 snd_soc_core
snd_rn_pci_acp3x 20480 0
snd_seq 114688 7 snd_seq_dummy
snd_seq_device 16384 1 snd_seq
snd_seq_dummy 12288 0
snd_soc_core 434176 4 snd_acp3x_rn,snd_sof,snd_soc_dmic,snd_acp3x_pdm_dma
snd_soc_dmic 12288 1
snd_sof 360448 2 snd_sof_amd_acp,snd_sof_pci
snd_sof_amd_acp 61440 1 snd_sof_amd_rembrandt
snd_sof_amd_rembrandt 16384 0
snd_sof_pci 24576 1 snd_sof_amd_rembrandt
snd_sof_utils 16384 1 snd_sof
snd_timer 53248 3 snd_seq,snd_hrtimer,snd_pcm
thinkpad_acpi 151552 0
ttm 106496 3 vmwgfx,amdgpu,drm_ttm_helper
uas 32768 0
usb_storage 86016 2 uas
uvcvideo 147456 0
vmwgfx 438272 0
xhci_hcd 352256 1 xhci_pci
xhci_pci 24576 0
################# dkms status ###############
command dkms is not present you should install dkms package
######### mokutil --sb-state #############
command mokutil is not present you should install mokutil package
########## sudo rfkill list #############
0: tpacpi_bluetooth_sw: Bluetooth
Soft blocked: no
Hard blocked: no
1: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
2: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
################ ping no-DNS ###################
ping gateway ipv4 : ok
ping gateway ipv6 : bad !
ping cloudflare ipv4 : ok
ping cloudflare ipv6 : ok
########### sudo ufw status #############
command ufw is not present you should install ufw package
######### resolvectl | grep Server #########
command resolvectl is not present you should install systemd package
###### cat /etc/network/interfaces #######
# ce fichier est obsolète sauf si vous savez ce que vous faîtes #
auto lo
iface lo inet loopback
######## sudo lshw -C network #########
command lshw is not present you should install lshw package
######## PCMCIA card info #############
'pccardctl' is not installed (package "pcmciautils").
################ ip a ###################
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
link/ether 74:5d:22:89:4e:3f brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 14:ac:60:25:60:67 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.25/24 brd 192.168.1.255 scope global dynamic noprefixroute wlan0
valid_lft 3152sec preferred_lft 3152sec
inet6 fdb3:1dd:11aa:10::7bd/128 scope global noprefixroute
valid_lft forever preferred_lft forever
inet6 2a0d:3344:2343:1110::7bd/128 scope global dynamic noprefixroute
valid_lft 925sec preferred_lft 325sec
inet6 2a0d:3344:2343:1110:19a:871f:a973:eddc/64 scope global dynamic noprefixroute
valid_lft 926sec preferred_lft 326sec
inet6 fdb3:1dd:11aa:10:6c61:c7c5:a215:d392/64 scope global noprefixroute
valid_lft forever preferred_lft forever
inet6 fe80::1bce:647e:ad3b:5493/64 scope link noprefixroute
valid_lft forever preferred_lft forever
####### modinfo <wifi_modules> |grep parm #######
Modules parm for amdgpu :
parm: vramlimit:Restrict VRAM for testing, in megabytes (int)
parm: vis_vramlimit:Restrict visible VRAM for testing, in megabytes (int)
parm: gartsize:Size of kernel GART to setup in megabytes (32, 64, etc., -1=auto) (uint)
parm: gttsize:Size of the GTT userspace domain in megabytes (-1 = auto) (int)
parm: moverate:Maximum buffer migration rate in MB/s. (32, 64, etc., -1=auto, 0=1=disabled) (int)
parm: audio:Audio enable (-1 = auto, 0 = disable, 1 = enable) (int)
parm: disp_priority:Display Priority (0 = auto, 1 = normal, 2 = high) (int)
parm: hw_i2c:hw i2c engine enable (0 = disable) (int)
parm: pcie_gen2:PCIE Gen2 mode (-1 = auto, 0 = disable, 1 = enable) (int)
parm: msi:MSI support (1 = enable, 0 = disable, -1 = auto) (int)
parm: lockup_timeout:GPU lockup timeout in ms (default: for bare metal 10000 for non-compute jobs and 60000 for compute jobs; for passthrough or sriov, 10000 for all jobs. 0: keep default value. negative: infinity timeout), format: for bare metal [Non-Compute] or [GFX,Compute,SDMA,Video]; for passthrough or sriov [all jobs] or [GFX,Compute,SDMA,Video]. (string)
parm: dpm:DPM support (1 = enable, 0 = disable, -1 = auto) (int)
parm: fw_load_type:firmware loading type (3 = rlc backdoor autoload if supported, 2 = smu load if supported, 1 = psp load, 0 = force direct if supported, -1 = auto) (int)
parm: aspm:ASPM support (1 = enable, 0 = disable, -1 = auto) (int)
parm: runpm:PX runtime pm (2 = force enable with BAMACO, 1 = force enable with BACO, 0 = disable, -1 = auto, -2 = autowith displays) (int)
parm: ip_block_mask:IP Block Mask (all blocks enabled (default)) (uint)
parm: bapm:BAPM support (1 = enable, 0 = disable, -1 = auto) (int)
parm: deep_color:Deep Color support (1 = enable, 0 = disable (default)) (int)
parm: vm_size:VM address space size in gigabytes (default 64GB) (int)
parm: vm_fragment_size:VM fragment size in bits (4, 5, etc. 4 = 64K (default), Max 9 = 2M) (int)
parm: vm_block_size:VM page table size in bits (default depending on vm_size) (int)
parm: vm_fault_stop:Stop on VM fault (0 = never (default), 1 = print first, 2 = always) (int)
parm: vm_debug:Debug VM handling (0 = disabled (default), 1 = enabled) (int)
parm: vm_update_mode:VM update using CPU (0 = never (default except for large BAR(LB)), 1 = Graphics only, 2 = Compute only (default for LB), 3 = Both (int)
parm: exp_hw_support:experimental hw support (1 = enable, 0 = disable (default)) (int)
parm: dc:Display Core driver (1 = enable, 0 = disable, -1 = auto (default)) (int)
parm: sched_jobs:the max number of jobs supported in the sw queue (default 32) (int)
parm: sched_hw_submission:the max number of HW submissions (default 2) (int)
parm: ppfeaturemask:all power features enabled (default)) (hexint)
parm: forcelongtraining:force memory long training (uint)
parm: pcie_gen_cap:PCIE Gen Caps (0: autodetect (default)) (uint)
parm: pcie_lane_cap:PCIE Lane Caps (0: autodetect (default)) (uint)
parm: cg_mask:Clockgating flags mask (0 = disable clock gating) (ullong)
parm: pg_mask:Powergating flags mask (0 = disable power gating) (uint)
parm: sdma_phase_quantum:SDMA context switch phase quantum (x 1K GPU clock cycles, 0 = no change (default 32)) (uint)
parm: disable_cu:Disable CUs (se.sh.cu,...) (charp)
parm: virtual_display:Enable virtual display feature (the virtual_display will be set like xxxx:xx:xx.x,x;xxxx:xx:xx.x,x) (charp)
parm: lbpw:Load Balancing Per Watt (LBPW) support (1 = enable, 0 = disable, -1 = auto) (int)
parm: compute_multipipe:Force compute queues to be spread across pipes (1 = enable, 0 = disable, -1 = auto) (int)
parm: gpu_recovery:Enable GPU recovery mechanism, (1 = enable, 0 = disable, -1 = auto) (int)
parm: emu_mode:Emulation mode, (1 = enable, 0 = disable) (int)
parm: ras_enable:Enable RAS features on the GPU (0 = disable, 1 = enable, -1 = auto (default)) (int)
parm: ras_mask:Mask of RAS features to enable (default 0xffffffff), only valid when ras_enable == 1 (uint)
parm: timeout_fatal_disable:disable watchdog timeout fatal error (false = default) (bool)
parm: timeout_period:watchdog timeout period (0 = timeout disabled, 1 ~ 0x23 = timeout maxcycles = (1 << period) (uint)
parm: si_support:SI support (1 = enabled, 0 = disabled (default)) (int)
parm: cik_support:CIK support (1 = enabled, 0 = disabled (default)) (int)
parm: smu_memory_pool_size:reserve gtt for smu debug usage, 0 = disable,0x1 = 256Mbyte, 0x2 = 512Mbyte, 0x4 = 1 Gbyte, 0x8 = 2GByte (uint)
parm: async_gfx_ring:Asynchronous GFX rings that could be configured with either different priorities (HP3D ring and LP3D ring), or equal priorities (0 = disabled, 1 = enabled (default)) (int)
parm: mcbp:Enable Mid-command buffer preemption (0 = disabled, 1 = enabled), -1 = auto (default) (int)
parm: discovery:Allow driver to discover hardware IPs from IP Discovery table at the top of VRAM (int)
parm: mes:Enable Micro Engine Scheduler (0 = disabled (default), 1 = enabled) (int)
parm: mes_kiq:Enable Micro Engine Scheduler KIQ (0 = disabled (default), 1 = enabled) (int)
parm: noretry:Disable retry faults (0 = retry enabled, 1 = retry disabled, -1 auto (default)) (int)
parm: force_asic_type:A non negative value used to specify the asic type for all supported GPUs (int)
parm: use_xgmi_p2p:Enable XGMI P2P interface (0 = disable; 1 = enable (default)) (int)
parm: sched_policy:Scheduling policy (0 = HWS (Default), 1 = HWS without over-subscription, 2 = Non-HWS (Used for debugging only) (int)
parm: hws_max_conc_proc:Max # processes HWS can execute concurrently when sched_policy=0 (0 = no concurrency, #VMIDs for KFD = Maximum(default)) (int)
parm: cwsr_enable:CWSR enable (0 = Off, 1 = On (Default)) (int)
parm: max_num_of_queues_per_device:Maximum number of supported queues per device (1 = Minimum, 4096 = default) (int)
parm: send_sigterm:Send sigterm to HSA process on unhandled exception (0 = disable, 1 = enable) (int)
parm: debug_largebar:Debug large-bar flag used to simulate large-bar capability on non-large bar machine (0 = disable, 1 = enable) (int)
parm: halt_if_hws_hang:Halt if HWS hang is detected (0 = off (default), 1 = on) (int)
parm: hws_gws_support:Assume MEC2 FW supports GWS barriers (false = rely on FW version check (Default), true = force supported) (bool)
parm: queue_preemption_timeout_ms:queue preemption timeout in ms (1 = Minimum, 9000 = default) (int)
parm: debug_evictions:enable eviction debug messages (false = default) (bool)
parm: no_system_mem_limit:disable system memory limit (false = default) (bool)
parm: no_queue_eviction_on_vm_fault:No queue eviction on VM fault (0 = queue eviction, 1 = no queue eviction) (int)
parm: mtype_local:MTYPE for local memory (0 = MTYPE_RW (default), 1 = MTYPE_NC, 2 = MTYPE_CC) (int)
parm: dcfeaturemask:all stable DC features enabled (default)) (uint)
parm: dcdebugmask:all debug options disabled (default)) (uint)
parm: visualconfirm:Visual confirm (0 = off (default), 1 = MPO, 5 = PSR) (uint)
parm: abmlevel:ABM level (0 = off (default), 1-4 = backlight reduction level) (uint)
parm: backlight:Backlight control (0 = pwm, 1 = aux, -1 auto (default)) (bint)
parm: tmz:Enable TMZ feature (-1 = auto (default), 0 = off, 1 = on) (int)
parm: reset_method:GPU reset method (-1 = auto (default), 0 = legacy, 1 = mode0, 2 = mode1, 3 = mode2, 4 = baco/bamaco) (int)
parm: bad_page_threshold:Bad page threshold(-1 = ignore threshold (default value), 0 = disable bad page retirement, -2 = driver sets threshold) (int)
parm: num_kcq:number of kernel compute queue user want to setup (8 if set to greater than 8 or less than 0, only affect gfx 8+) (int)
parm: vcnfw_log:Enable vcnfw log(0 = disable (default value), 1 = enable) (int)
parm: sg_display:S/G Display (-1 = auto (default), 0 = disable) (int)
parm: smu_pptable_id:specify pptable id to be used (-1 = auto(default) value, 0 = use pptable from vbios, > 0 = soft pptable id) (int)
parm: user_partt_mode:specify partition mode to be used (-2 = AMDGPU_AUTO_COMPUTE_PARTITION_MODE(default value) 0 = AMDGPU_SPX_PARTITION_MODE, 1 = AMDGPU_DPX_PARTITION_MODE, 2 = AMDGPU_TPX_PARTITION_MODE, 3 = AMDGPU_QPX_PARTITION_MODE, 4 = AMDGPU_CPX_PARTITION_MODE) (uint)
parm: enforce_isolation:enforce process isolation between graphics and compute . enforce_isolation = on (bool)
Modules parm for amdxcp :
Modules parm for bluetooth :
parm: disable_esco:Disable eSCO connection creation (bool)
parm: disable_ertm:Disable enhanced retransmission mode (bool)
parm: enable_ecred:Enable enhanced credit flow control mode (bool)
Modules parm for btbcm :
Modules parm for btintel :
Modules parm for btmtk :
Modules parm for btrtl :
Modules parm for btusb :
parm: disable_scofix:Disable fixup of wrong SCO buffer size (bool)
parm: force_scofix:Force fixup of wrong SCO buffers size (bool)
parm: enable_autosuspend:Enable USB autosuspend by default (bool)
parm: reset:Send HCI reset command on initialization (bool)
Modules parm for cfg80211 :
parm: bss_entries_limit:limit to number of scan BSS entries (per wiphy, default 1000) (int)
parm: ieee80211_regdom:IEEE 802.11 regulatory domain code (charp)
parm: cfg80211_disable_40mhz_24ghz:Disable 40MHz support in the 2.4GHz band (bool)
Modules parm for drm_buddy :
Modules parm for drm_display_helper :
parm: drm_dp_cec_unregister_delay:CEC unregister delay in seconds, 0: no delay, >= 1000: never unregister (uint)
parm: dp_aux_i2c_speed_khz:Assumed speed of the i2c bus in kHz, (1-400, default 10) (int)
parm: dp_aux_i2c_transfer_size:Number of bytes to transfer in a single I2C over DP AUX CH message, (1-16, default 16) (int)
Modules parm for drm_exec :
Modules parm for drm_kms_helper :
parm: fbdev_emulation:Enable legacy fbdev emulation [default=true] (bool)
parm: drm_fbdev_overalloc:Overallocation of the fbdev buffer (%) [default=100] (int)
parm: poll:bool
parm: edid_firmware:DEPRECATED. Use drm.edid_firmware module parameter instead. (charp)
Modules parm for drm_suballoc_helper :
Modules parm for drm_ttm_helper :
Modules parm for gpu_sched :
parm: sched_policy:Specify the scheduling policy for entities on a run-queue, 0 = Round Robin, 1 = FIFO (default). (int)
Modules parm for hid_generic :
Modules parm for hid_multitouch :
Modules parm for i2c_hid :
Modules parm for i2c_hid_acpi :
Modules parm for mac80211 :
parm: minstrel_vht_only:Use only VHT rates when VHT is supported by sta. (bool)
parm: max_nullfunc_tries:Maximum nullfunc tx tries before disconnecting (reason 4). (int)
parm: max_probe_tries:Maximum probe tries before disconnecting (reason 4). (int)
parm: beacon_loss_count:Number of beacon intervals before we decide beacon was lost. (int)
parm: probe_wait_ms:Maximum time(ms) to wait for probe response before disconnecting (reason 4). (int)
parm: ieee80211_default_rc_algo:Default rate control algorithm for mac80211 to use (charp)
Modules parm for mt76 :
Modules parm for mt76_connac_lib :
Modules parm for mt7921_common :
parm: disable_clc:disable CLC support (bool)
Modules parm for mt7921e :
parm: disable_aspm:disable PCI ASPM support (bool)
Modules parm for mt792x_lib :
Modules parm for snd :
parm: max_user_ctl_alloc_size:Max allocation size for user controls (int)
parm: slots:Module names assigned to the slots. (array of charp)
parm: major:Major # for sound driver. (int)
parm: cards_limit:Count of auto-loadable soundcards. (int)
Modules parm for snd_acp3x_pdm_dma :
parm: pdm_gain:Gain control (0-3) (int)
Modules parm for snd_acp3x_rn :
Modules parm for snd_acp_config :
Modules parm for snd_compress :
Modules parm for snd_ctl_led :
Modules parm for snd_hda_codec :
parm: dump_coef:Dump processing coefficients in codec proc file (-1=auto, 0=disable, 1=enable) (int)
Modules parm for snd_hda_codec_conexant :
Modules parm for snd_hda_codec_generic :
Modules parm for snd_hda_codec_hdmi :
parm: static_hdmi_pcm:Don't restrict PCM parameters per ELD info (bool)
parm: enable_acomp:Enable audio component binding (default=yes) (bool)
parm: enable_silent_stream:Enable Silent Stream for HDMI devices (bool)
parm: enable_all_pins:Forcibly enable all pins (bool)
Modules parm for snd_hda_core :
Modules parm for snd_hda_intel :
parm: index:Index value for Intel HD audio interface. (array of int)
parm: id:ID string for Intel HD audio interface. (array of charp)
parm: enable:Enable Intel HD audio interface. (array of bool)
parm: model:Use the given board model. (array of charp)
parm: position_fix:DMA pointer read method.(-1 = system default, 0 = auto, 1 = LPIB, 2 = POSBUF, 3 = VIACOMBO, 4 = COMBO, 5 = SKL+, 6 = FIFO). (array of int)
parm: bdl_pos_adj:BDL position adjustment offset. (array of int)
parm: probe_mask:Bitmask to probe codecs (default = -1). (array of int)
parm: probe_only:Only probing and no codec initialization. (array of int)
parm: jackpoll_ms:Ms between polling for jack events (default = 0, using unsol events only) (array of int)
parm: single_cmd:Use single command to communicate with codecs (for debugging only). (bint)
parm: enable_msi:Enable Message Signaled Interrupt (MSI) (bint)
parm: patch:Patch file for Intel HD audio interface. (array of charp)
parm: beep_mode:Select HDA Beep registration mode (0=off, 1=on) (default=1). (array of bool)
parm: dmic_detect:Allow DSP driver selection (bypass this driver) (0=off, 1=on) (default=1); deprecated, use snd-intel-dspcfg.dsp_driver option instead (bool)
parm: ctl_dev_id:Use control device identifier (based on codec address). (bool)
parm: power_save:Automatic power-saving timeout (in second, 0 = disable). (xint)
parm: pm_blacklist:Enable power-management denylist (bool)
parm: power_save_controller:Reset controller in power save mode. (bool)
parm: align_buffer_size:Force buffer and period sizes to be multiple of 128 bytes. (bint)
parm: snoop:Enable/disable snooping (bint)
Modules parm for snd_hrtimer :
Modules parm for snd_hwdep :
Modules parm for snd_pci_acp5x :
Modules parm for snd_pci_acp6x :
Modules parm for snd_pci_ps :
Modules parm for snd_pcm :
parm: preallocate_dma:Preallocate DMA memory when the PCM devices are initialized. (int)
parm: maximum_substreams:Maximum substreams with preallocated DMA memory. (int)
parm: max_alloc_per_card:Max total allocation bytes per card. (ulong)
Modules parm for snd_pcm_dmaengine :
Modules parm for snd_rn_pci_acp3x :
parm: acp_power_gating:Enable acp power gating (int)
parm: dmic_acpi_check:Digital microphone presence (-1=auto, 0=none, 1=force) (bint)
Modules parm for snd_seq :
parm: seq_client_load:The numbers of global (system) clients to load through kmod. (array of int)
parm: seq_default_timer_class:The default timer class. (int)
parm: seq_default_timer_sclass:The default timer slave class. (int)
parm: seq_default_timer_card:The default timer card number. (int)
parm: seq_default_timer_device:The default timer device number. (int)
parm: seq_default_timer_subdevice:The default timer subdevice number. (int)
parm: seq_default_timer_resolution:The default timer resolution in Hz. (int)
Modules parm for snd_seq_device :
Modules parm for snd_seq_dummy :
parm: ports:number of ports to be created (int)
parm: duplex:create DUPLEX ports (bool)
Modules parm for snd_soc_core :
parm: prealloc_buffer_size_kbytes:Preallocate DMA buffer size (KB). (uint)
parm: pmdown_time:DAPM stream powerdown time (msecs) (int)
Modules parm for snd_soc_dmic :
parm: modeswitch_delay:uint
parm: wakeup_delay:uint
Modules parm for snd_sof :
parm: ipc4_ignore_cpc:Ignore CPC values. This option will disable clock scaling in firmware. (bool)
parm: sof_debug:SOF core debug options (0x0 all off) (int)
Modules parm for snd_sof_amd_acp :
parm: enable_fw_debug:Enable Firmware debug (bool)
Modules parm for snd_sof_amd_rembrandt :
Modules parm for snd_sof_pci :
parm: fw_path:alternate path for SOF firmware. (charp)
parm: fw_filename:alternate filename for SOF firmware. (charp)
parm: lib_path:alternate path for SOF firmware libraries. (charp)
parm: tplg_path:alternate path for SOF topology. (charp)
parm: tplg_filename:alternate filename for SOF topology. (charp)
parm: sof_pci_debug:SOF PCI debug options (0x0 all off) (int)
parm: ipc_type:SOF IPC type (0): SOF, (1) Intel CAVS (int)
Modules parm for snd_sof_utils :
Modules parm for snd_timer :
parm: timer_limit:Maximum global timers in system. (int)
parm: timer_tstamp_monotonic:Use posix monotonic clock source for timestamps (default). (int)
Modules parm for thinkpad_acpi :
parm: experimental:Enables experimental features when non-zero (int)
parm: debug:Sets debug level bit-mask (uint)
parm: force_load:Attempts to load the driver even on a mis-identified ThinkPad when true (bool)
parm: fan_control:Enables setting fan parameters features when true (bool)
parm: brightness_mode:Selects brightness control strategy: 0=auto, 1=EC, 2=UCMS, 3=EC+NVRAM (uint)
parm: brightness_enable:Enables backlight control when 1, disables when 0 (uint)
parm: volume_mode:Selects volume control strategy: 0=auto, 1=EC, 2=N/A, 3=EC+NVRAM (uint)
parm: volume_capabilities:Selects the mixer capabilities: 0=auto, 1=volume and mute, 2=mute only (uint)
parm: volume_control:Enables software override for the console audio control when true (bool)
parm: software_mute:Request full software mute control (bool)
parm: index:ALSA index for the ACPI EC Mixer (int)
parm: id:ALSA id for the ACPI EC Mixer (charp)
parm: enable:Enable the ALSA interface for the ACPI EC Mixer (bool)
parm: hotkey:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: bluetooth:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: video:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: light:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: cmos:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: led:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: beep:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: brightness:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: volume:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: fan:Simulates thinkpad-acpi procfs command at module load, see documentation
parm: profile_force:Force profile mode. -1=off, 1=MMC, 2=PSC (int)
Modules parm for ttm :
parm: page_pool_size:Number of pages in the WC/UC/DMA pool (ulong)
parm: pages_limit:Limit for the allocated pages (ulong)
parm: dma32_pages_limit:Limit for the allocated DMA32 pages (ulong)
Modules parm for uas :
Modules parm for usb_storage :
parm: option_zero_cd:ZeroCD mode (1=Force Modem (default), 2=Allow CD-Rom (uint)
parm: swi_tru_install:TRU-Install mode (1=Full Logic (def), 2=Force CD-Rom, 3=Force Modem) (uint)
parm: delay_use:seconds to delay before using a new device (uint)
parm: quirks:supplemental list of device IDs and their quirks (string)
Modules parm for uvcvideo :
parm: clock:Video buffers timestamp clock
parm: hwtimestamps:Use hardware timestamps (uint)
parm: nodrop:Don't drop incomplete frames (uint)
parm: quirks:Forced device quirks (uint)
parm: trace:Trace level bitmask (uint)
parm: timeout:Streaming control requests timeout (uint)
Modules parm for vmwgfx :
parm: restrict_iommu:Try to limit IOMMU usage for TTM pages (int)
parm: force_coherent:Force coherent TTM pages (int)
parm: restrict_dma_mask:Restrict DMA mask to 44 bits with IOMMU (int)
parm: assume_16bpp:Assume 16-bpp when filtering modes (int)
Modules parm for xhci_hcd :
parm: link_quirk:Don't clear the chain bit on a link TRB (int)
parm: quirks:Bit flags for quirks to be enabled as default (ullong)
Modules parm for xhci_pci :
####### systemctl list network units #########
networking.service loaded active exited Raise network interfaces
NetworkManager-wait-online.service loaded active exited Network Manager Wait Online
NetworkManager.service loaded active running Network Manager
systemd-networkd.service loaded inactive dead Network Configuration
systemd-timesyncd.service loaded inactive dead Network Time Synchronization
wpa_supplicant.service loaded active running WPA supplicant
######## nmcli connection show ###########
NAME UUID TYPE DEVICE
RouteurStarlink5ghz 74ec8d72-bc53-4ce5-a5d2-625c0c55f006 wifi wlan0
lo a4da185d-8d98-412f-874f-ffc91ca75c29 loopback lo
Wired connection 1 401879a4-bfdd-352e-ac90-65b5e0cb6515 ethernet --
######### nmcli -f all d show wlan0 #############
GENERAL.DEVICE: wlan0
GENERAL.TYPE: wifi
GENERAL.NM-TYPE: NMDeviceWifi
GENERAL.DBUS-PATH: /org/freedesktop/NetworkManager/Devices/3
GENERAL.VENDOR: MEDIATEK Corp.
GENERAL.PRODUCT: MT7921 802.11ax PCI Express Wireless Network Adapter
GENERAL.DRIVER: mt7921e
GENERAL.DRIVER-VERSION: 6.6.9-amd64
GENERAL.FIRMWARE-VERSION: ____010000-20230526130958
GENERAL.HWADDR: 14:AC:60:25:60:67
GENERAL.MTU: 1500
GENERAL.STATE: 100 (connected)
GENERAL.REASON: 0 (No reason given)
GENERAL.IP4-CONNECTIVITY: 4 (full)
GENERAL.IP6-CONNECTIVITY: 4 (full)
GENERAL.UDI: /sys/devices/pci0000:00/0000:00:02.3/0000:03:00.0/net/wlan0
GENERAL.PATH: pci-0000:03:00.0
GENERAL.IP-IFACE: wlan0
GENERAL.IS-SOFTWARE: no
GENERAL.NM-MANAGED: yes
GENERAL.AUTOCONNECT: yes
GENERAL.FIRMWARE-MISSING: no
GENERAL.NM-PLUGIN-MISSING: no
GENERAL.PHYS-PORT-ID: --
GENERAL.CONNECTION: RouteurStarlink5ghz
GENERAL.CON-UUID: 74ec8d72-bc53-4ce5-a5d2-625c0c55f006
GENERAL.CON-PATH: /org/freedesktop/NetworkManager/ActiveConnection/2
GENERAL.METERED: no (guessed)
CAPABILITIES.CARRIER-DETECT: no
CAPABILITIES.SPEED: 104 Mb/s
CAPABILITIES.IS-SOFTWARE: no
CAPABILITIES.SRIOV: no
INTERFACE-FLAGS.UP: yes
INTERFACE-FLAGS.LOWER-UP: yes
INTERFACE-FLAGS.CARRIER: yes
INTERFACE-FLAGS.PROMISC: no
WIFI-PROPERTIES.WEP: yes
WIFI-PROPERTIES.WPA: yes
WIFI-PROPERTIES.WPA2: yes
WIFI-PROPERTIES.TKIP: yes
WIFI-PROPERTIES.CCMP: yes
WIFI-PROPERTIES.AP: yes
WIFI-PROPERTIES.ADHOC: no
WIFI-PROPERTIES.2GHZ: yes
WIFI-PROPERTIES.5GHZ: yes
WIFI-PROPERTIES.MESH: no
WIFI-PROPERTIES.IBSS-RSN: no
AP[1].IN-USE:
AP[1].BSSID: 3E:B3:01:4D:11:AA
AP[1].SSID: --
AP[1].MODE: Infra
AP[1].CHAN: 11
AP[1].RATE: 195 Mbit/s
AP[1].SIGNAL: 60
AP[1].BARS: ▂▄▆_
AP[1].SECURITY: WPA2
AP[2].IN-USE: *
AP[2].BSSID: 3E:B3:01:2D:11:AA
AP[2].SSID: RouteurStarlink5ghz
AP[2].MODE: Infra
AP[2].CHAN: 11
AP[2].RATE: 195 Mbit/s
AP[2].SIGNAL: 55
AP[2].BARS: ▂▄__
AP[2].SECURITY: WPA2
AP[3].IN-USE:
AP[3].BSSID: 3E:B3:01:6D:11:AA
AP[3].SSID: --
AP[3].MODE: Infra
AP[3].CHAN: 11
AP[3].RATE: 195 Mbit/s
AP[3].SIGNAL: 55
AP[3].BARS: ▂▄__
AP[3].SECURITY: WPA2
AP[4].IN-USE:
AP[4].BSSID: 3E:B3:01:3D:11:AA
AP[4].SSID: RouteurStarlink5ghz
AP[4].MODE: Infra
AP[4].CHAN: 36
AP[4].RATE: 405 Mbit/s
AP[4].SIGNAL: 44
AP[4].BARS: ▂▄__
AP[4].SECURITY: WPA2
AP[5].IN-USE:
AP[5].BSSID: 3E:B3:01:5D:11:AA
AP[5].SSID: --
AP[5].MODE: Infra
AP[5].CHAN: 36
AP[5].RATE: 405 Mbit/s
AP[5].SIGNAL: 44
AP[5].BARS: ▂▄__
AP[5].SECURITY: WPA2
IP4.ADDRESS[1]: 192.168.1.25/24
IP4.GATEWAY: 192.168.1.1
IP4.ROUTE[1]: dst = 192.168.1.0/24, nh = 0.0.0.0, mt = 600
IP4.ROUTE[2]: dst = 0.0.0.0/0, nh = 192.168.1.1, mt = 600
IP4.DNS[1]: 192.168.1.1
IP4.DOMAIN[1]: lan
DHCP4.OPTION[1]: dhcp_client_identifier = 01:14:ac:60:25:60:67
DHCP4.OPTION[2]: dhcp_lease_time = 3600
DHCP4.OPTION[3]: dhcp_server_identifier = 192.168.1.1
DHCP4.OPTION[4]: domain_name = lan
DHCP4.OPTION[5]: domain_name_servers = 192.168.1.1
DHCP4.OPTION[6]: expiry = 1709642974
DHCP4.OPTION[7]: ip_address = 192.168.1.25
DHCP4.OPTION[8]: next_server = 192.168.1.1
DHCP4.OPTION[9]: requested_broadcast_address = 1
DHCP4.OPTION[10]: requested_domain_name = 1
DHCP4.OPTION[11]: requested_domain_name_servers = 1
DHCP4.OPTION[12]: requested_domain_search = 1
DHCP4.OPTION[13]: requested_host_name = 1
DHCP4.OPTION[14]: requested_interface_mtu = 1
DHCP4.OPTION[15]: requested_ms_classless_static_routes = 1
DHCP4.OPTION[16]: requested_nis_domain = 1
DHCP4.OPTION[17]: requested_nis_servers = 1
DHCP4.OPTION[18]: requested_ntp_servers = 1
DHCP4.OPTION[19]: requested_rfc3442_classless_static_routes = 1
DHCP4.OPTION[20]: requested_root_path = 1
DHCP4.OPTION[21]: requested_routers = 1
DHCP4.OPTION[22]: requested_static_routes = 1
DHCP4.OPTION[23]: requested_subnet_mask = 1
DHCP4.OPTION[24]: requested_time_offset = 1
DHCP4.OPTION[25]: requested_wpad = 1
DHCP4.OPTION[26]: routers = 192.168.1.1
DHCP4.OPTION[27]: subnet_mask = 255.255.255.0
IP6.ADDRESS[1]: fdb3:1dd:11aa:10::7bd/128
IP6.ADDRESS[2]: 2a0d:3344:2343:1110::7bd/128
IP6.ADDRESS[3]: 2a0d:3344:2343:1110:19a:871f:a973:eddc/64
IP6.ADDRESS[4]: fdb3:1dd:11aa:10:6c61:c7c5:a215:d392/64
IP6.ADDRESS[5]: fe80::1bce:647e:ad3b:5493/64
IP6.GATEWAY: fe80::7624:9fff:fec2:5d20
IP6.ROUTE[1]: dst = fe80::/64, nh = ::, mt = 1024
IP6.ROUTE[2]: dst = fdb3:1dd:11aa:10::/64, nh = ::, mt = 600
IP6.ROUTE[3]: dst = 2a0d:3344:2343:1110::/64, nh = ::, mt = 600
IP6.ROUTE[4]: dst = fdb3:1dd:11aa::/48, nh = fe80::7624:9fff:fec2:5d20, mt = 600
IP6.ROUTE[5]: dst = 2a0d:3344:2343:1100::/56, nh = fe80::7624:9fff:fec2:5d20, mt = 600
IP6.ROUTE[6]: dst = ::/0, nh = fe80::7624:9fff:fec2:5d20, mt = 600
IP6.ROUTE[7]: dst = fdb3:1dd:11aa:10::7bd/128, nh = ::, mt = 600
IP6.ROUTE[8]: dst = 2a0d:3344:2343:1110::7bd/128, nh = ::, mt = 600
IP6.DNS[1]: fdb3:1dd:11aa:10::1
DHCP6.OPTION[1]: dhcp6_client_id = 00:04:6a:3b:5b:0c:f7:2a:e1:fe:26:e0:22:b9:58:5c:58:22
DHCP6.OPTION[2]: dhcp6_name_servers = fdb3:1dd:11aa:10::1
DHCP6.OPTION[3]: iaid = d2:59:86:4f
DHCP6.OPTION[4]: ip6_address = fdb3:1dd:11aa:10::7bd 2a0d:3344:2343:1110::7bd
CONNECTIONS.AVAILABLE-CONNECTION-PATHS: /org/freedesktop/NetworkManager/Settings/3
CONNECTIONS.AVAILABLE-CONNECTIONS[1]: 74ec8d72-bc53-4ce5-a5d2-625c0c55f006 | RouteurStarlink5ghz
######### iw dev wlan0 link #############
Connected to 3e:b3:01:2d:11:aa (on wlan0)
SSID: RouteurStarlink5ghz
freq: 2462
RX: 30431327 bytes (25558 packets)
TX: 1448545 bytes (12338 packets)
signal: -65 dBm
rx bitrate: 26.0 MBit/s MCS 3
tx bitrate: 130.0 MBit/s MCS 15
bss flags: short-preamble short-slot-time
dtim period: 1
beacon int: 100
#### iptables -vL -t filter|nat|mangle|raw|security #####
\n ### table filter ###
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table nat ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table mangle ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain POSTROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table raw ###
Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
\n ### table security ###
Chain INPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
######## iw list ###########
Wiphy phy0
wiphy index: 0
max # scan SSIDs: 4
max scan IEs length: 482 bytes
max # sched scan SSIDs: 10
max # match sets: 16
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Supported interface modes:
* managed
* AP
* AP/VLAN
* monitor
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x9ff
RX LDPC
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-15
HE Iftypes: managed
HE MAC Capabilities (0x08011a000040):
+HTC HE Supported
Trigger Frame MAC Padding Duration: 2
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x2270ce120dc0b306423f00):
HE40/2.4GHz
242 tone RUs/2.4GHz
Device Class: 1
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
Partial Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformee
Beamformee STS <= 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered CQI Feedback
Partial Bandwidth Extended Range
PPE Threshold Present
Power Boost Factor ar
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
20MHz in 40MHz HE PPDU 2.4GHz
DCM Max BW: 1
Longer Than 16HE SIG-B OFDM Symbols
Non-Triggered CQI Feedback
TX 1024-QAM
RX 1024-QAM
RX Full BW SU Using HE MU PPDU with Compression SIGB
RX Full BW SU Using HE MU PPDU with Non-Compression SIGB
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x39 0x1c 0xc7 0x71 0x1c 0x07
EHT Iftypes: managed
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw=20 MHz, max NSS for MCS 0-7: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: AP
HE MAC Capabilities (0x00011a081044):
+HTC HE Supported
BSR
OM Control
Maximum A-MPDU Length Exponent: 3
BQR
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x0220ce120000a000000c00):
HE40/2.4GHz
LDPC Coding in Payload
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
Partial Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
Partial Bandwidth Extended Range
PPE Threshold Present
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x39 0x1c 0xc7 0x71 0x1c 0x07
EHT Iftypes: AP
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw=20 MHz, max NSS for MCS 0-7: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw=20 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Bitrates (non-HT):
* 1.0 Mbps (short preamble supported)
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Band 2:
Capabilities: 0x9ff
RX LDPC
HT20/HT40
SM Power Save disabled
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: No restriction (0x00)
HT TX/RX MCS rate indexes supported: 0-15
VHT Capabilities (0x339071b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformee
MU Beamformee
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT extended NSS: supported
HE Iftypes: managed
HE MAC Capabilities (0x08011a000040):
+HTC HE Supported
Trigger Frame MAC Padding Duration: 2
OM Control
Maximum A-MPDU Length Exponent: 3
A-MSDU in A-MPDU
HE PHY Capabilities: (0x4470ce120dc0b306423f00):
HE40/HE80/5GHz
242 tone RUs/5GHz
Device Class: 1
LDPC Coding in Payload
HE SU PPDU with 1x HE-LTF and 0.8us GI
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
Partial Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
SU Beamformee
Beamformee STS <= 80Mhz: 3
Ng = 16 SU Feedback
Ng = 16 MU Feedback
Codebook Size SU Feedback
Codebook Size MU Feedback
Triggered CQI Feedback
Partial Bandwidth Extended Range
PPE Threshold Present
Power Boost Factor ar
HE SU PPDU & HE PPDU 4x HE-LTF 0.8us GI
20MHz in 40MHz HE PPDU 2.4GHz
DCM Max BW: 1
Longer Than 16HE SIG-B OFDM Symbols
Non-Triggered CQI Feedback
TX 1024-QAM
RX 1024-QAM
RX Full BW SU Using HE MU PPDU with Compression SIGB
RX Full BW SU Using HE MU PPDU with Non-Compression SIGB
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x39 0x1c 0xc7 0x71 0x1c 0x07
EHT Iftypes: managed
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
HE Iftypes: AP
HE MAC Capabilities (0x00011a081044):
+HTC HE Supported
BSR
OM Control
Maximum A-MPDU Length Exponent: 3
BQR
A-MSDU in A-MPDU
OM Control UL MU Data Disable RX
HE PHY Capabilities: (0x0420ce120000a000000c00):
HE40/HE80/5GHz
LDPC Coding in Payload
NDP with 4x HE-LTF and 3.2us GI
STBC Tx <= 80MHz
STBC Rx <= 80MHz
Full Bandwidth UL MU-MIMO
Partial Bandwidth UL MU-MIMO
DCM Max Constellation: 2
DCM Max Constellation Rx: 2
Partial Bandwidth Extended Range
PPE Threshold Present
TX 1024-QAM
RX 1024-QAM
HE RX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
HE TX MCS and NSS set <= 80 MHz
1 streams: MCS 0-11
2 streams: MCS 0-11
3 streams: not supported
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
PPE Threshold 0x39 0x1c 0xc7 0x71 0x1c 0x07
EHT Iftypes: AP
EHT MAC Capabilities (0x0000):
EHT PHY Capabilities: (0x0000000000000000):
EHT MCS/NSS: (0x):
EHT bw <= 80 MHz, max NSS for MCS 8-9: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 10-11: Rx=0, Tx=0
EHT bw <= 80 MHz, max NSS for MCS 12-13: Rx=0, Tx=0
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (26.0 dBm) (radar detection)
* 5520 MHz [104] (26.0 dBm) (radar detection)
* 5540 MHz [108] (26.0 dBm) (radar detection)
* 5560 MHz [112] (26.0 dBm) (radar detection)
* 5580 MHz [116] (26.0 dBm) (radar detection)
* 5600 MHz [120] (26.0 dBm) (radar detection)
* 5620 MHz [124] (26.0 dBm) (radar detection)
* 5640 MHz [128] (26.0 dBm) (radar detection)
* 5660 MHz [132] (26.0 dBm) (radar detection)
* 5680 MHz [136] (26.0 dBm) (radar detection)
* 5700 MHz [140] (26.0 dBm) (radar detection)
* 5720 MHz [144] (13.0 dBm) (radar detection)
* 5745 MHz [149] (13.0 dBm)
* 5765 MHz [153] (13.0 dBm)
* 5785 MHz [157] (13.0 dBm)
* 5805 MHz [161] (13.0 dBm)
* 5825 MHz [165] (13.0 dBm)
* 5845 MHz [169] (13.0 dBm)
* 5865 MHz [173] (13.0 dBm)
* 5885 MHz [177] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* new_mpath
* set_mesh_config
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* join_mesh
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* tdls_mgmt
* tdls_oper
* start_sched_scan
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* channel_switch
* set_qos_map
* set_multicast_to_unicast
* set_sar_specs
WoWLAN support:
* wake up on disconnect
* wake up on magic packet
* wake up on pattern match, up to 1 patterns of 1-128 bytes,
maximum packet offset 0 bytes
* can do GTK rekeying
* wake up on network detection, up to 10 match sets
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed, P2P-client } <= 2, #{ AP, P2P-GO } <= 1,
total <= 2, #channels <= 2
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports active monitor (which will ACK incoming frames)
Driver/device bandwidth changes during BSS lifetime (AP/GO mode)
Device supports configuring vdev MAC-addr on create.
Device supports randomizing MAC-addr in scans.
Device supports randomizing MAC-addr in sched scans.
max # scan plans: 1
max scan plan interval: 65535
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ BEACON_RATE_LEGACY ]: legacy beacon rate setting
* [ BEACON_RATE_HT ]: HT beacon rate setting
* [ BEACON_RATE_VHT ]: VHT beacon rate setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CQM_RSSI_LIST ]: multiple CQM_RSSI_THOLD records
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ ACK_SIGNAL_SUPPORT ]: ack signal level support
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
* [ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
* [ AIRTIME_FAIRNESS ]: airtime fairness scheduling
* [ AQL ]: Airtime Queue Limits (AQL)
* [ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
* [ SCAN_FREQ_KHZ ]: scan on kHz frequency support
* [ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support
* [ BEACON_RATE_HE ]: HE beacon rate support (AP/mesh)
######## iw dev wlan0 station dump ###########
Station 3e:b3:01:2d:11:aa (on wlan0)
inactive time: 136 ms
rx bytes: 30431327
rx packets: 25558
tx bytes: 1448545
tx packets: 12338
tx retries: 251
tx failed: 0
beacon loss: 0
rx drop misc: 0
signal: -65 [-67, -68] dBm
signal avg: -66 [80, -70] dBm
tx bitrate: 130.0 MBit/s MCS 15
tx duration: 1666442 us
rx bitrate: 26.0 MBit/s MCS 3
rx duration: 6464547 us
last ack signal:-65 dBm
avg ack signal: -65 dBm
airtime weight: 256
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 1
beacon interval:100
short preamble: yes
short slot time:yes
connected time: 449 seconds
associated at [boottime]: 79.535s
associated at: 1709639374298 ms
current time: 1709639823298 ms
############ iw dev wlan0 scan ############
BSS 3e:b3:01:2d:11:aa(on wlan0) -- associated
last seen: 536.677s [boottime]
TSF: 164243143456 usec (1d, 21:37:23)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime RadioMeasure (0x1431)
signal: -67.00 dBm
last seen: 236 ms ago
Information elements from Probe Response frame:
SSID: RouteurStarlink5ghz
Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
DS Parameter set: channel 11
ERP: <no flags>
Extended supported rates: 6.0 12.0 24.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
HT capabilities:
Capabilities: 0x1ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* HT Information Exchange Supported
* BSS Transition
* Interworking
* WNM-Notification
* Max Number Of MSDUs In A-MSDU is unlimited
BSS Load:
* station count: 4
* channel utilisation: 27/255
* available admission capacity: 31250 [*32us]
802.11u Interworking:
Network Options: 0x0
Network Type: 0 (Private)
Venue Group: 2 (Business)
Venue Type: 8
HESSID: 3e:b3:01:2d:11:aa
802.11u Advertisement:
Query Response Info: 0x7f
Query Response Length Limit: 127
ANQP
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 3
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
RM enabled capabilities:
Capabilities: 0x02 0x00 0x00 0x00 0x00
Neighbor Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
AP Channel Report:
* operating class: 81
* channel(s): 1 2 3 4 5 6 7 8 9 10 11 12 13
Power constraint: 3 dB
TPC report: TX power: 63 dBm
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
VHT capabilities:
VHT Capabilities (0x33c279b1):
Max MPDU length: 7991
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
+HTC-VHT
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 260 Mbps
VHT TX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 260 Mbps
VHT extended NSS: not supported
VHT operation:
* channel width: 0 (20 or 40 MHz)
* center freq segment 1: 0
* center freq segment 2: 0
* VHT basic MCS set: 0xffe5
BSS 3e:b3:01:6d:11:aa(on wlan0)
last seen: 530.541s [boottime]
TSF: 164243149207 usec (1d, 21:37:23)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime RadioMeasure (0x1431)
signal: -67.00 dBm
last seen: 6372 ms ago
SSID:
Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
DS Parameter set: channel 11
TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 63 dBm
RM enabled capabilities:
Capabilities: 0x02 0x00 0x00 0x00 0x00
Neighbor Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
AP Channel Report:
* operating class: 81
* channel(s): 1 2 3 4 5 6 7 8 9 10 11 12 13
ERP: Barker_Preamble_Mode
Extended supported rates: 6.0 12.0 24.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
BSS Load:
* station count: 5
* channel utilisation: 20/255
* available admission capacity: 31250 [*32us]
HT capabilities:
Capabilities: 0x1ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
VHT capabilities:
VHT Capabilities (0x33c279b1):
Max MPDU length: 7991
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
+HTC-VHT
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 260 Mbps
VHT TX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 260 Mbps
VHT extended NSS: not supported
VHT operation:
* channel width: 0 (20 or 40 MHz)
* center freq segment 1: 0
* center freq segment 2: 0
* VHT basic MCS set: 0xffe5
Extended capabilities:
* HT Information Exchange Supported
* BSS Transition
* Interworking
* Max Number Of MSDUs In A-MSDU is unlimited
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 3
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 3e:b3:01:3d:11:aa(on wlan0)
last seen: 531.150s [boottime]
TSF: 164243728078 usec (1d, 21:37:23)
freq: 5180
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble RadioMeasure (0x1031)
signal: -75.00 dBm
last seen: 5764 ms ago
Information elements from Probe Response frame:
SSID: RouteurStarlink5ghz
Supported rates: 6.0* 9.0 12.0* 18.0 24.0* 36.0 48.0 54.0
DS Parameter set: channel 36
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
HT capabilities:
Capabilities: 0x1ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23, 32
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 36
* secondary channel offset: above
* STA channel width: any
* RIFS: 0
* HT protection: 20 MHz
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* BSS Transition
* Interworking
* WNM-Notification
* Operating Mode Notification
* Max Number Of MSDUs In A-MSDU is unlimited
802.11u Interworking:
Network Options: 0x0
Network Type: 0 (Private)
Venue Group: 2 (Business)
Venue Type: 8
HESSID: 3e:b3:01:3d:11:aa
802.11u Advertisement:
Query Response Info: 0x7f
Query Response Length Limit: 127
ANQP
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 3
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
RM enabled capabilities:
Capabilities: 0x02 0x00 0x00 0x00 0x00
Neighbor Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
AP Channel Report:
* operating class: 128
* channel(s): 42 58 106 122
Power constraint: 3 dB
TPC report: TX power: 63 dBm
Transmit Power Envelope:
* Local Maximum Transmit Power For 20 MHz: 15 dBm
* Local Maximum Transmit Power For 40 MHz: 15 dBm
* Local Maximum Transmit Power For 80 MHz: 15 dBm
Country: FR Environment: Indoor/Outdoor
Channels [42 - 54] @ -1 dBm
VHT capabilities:
VHT Capabilities (0x33c279b1):
Max MPDU length: 7991
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
+HTC-VHT
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 1170 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 1170 Mbps
VHT extended NSS: not supported
VHT operation:
* channel width: 1 (80 MHz)
* center freq segment 1: 42
* center freq segment 2: 0
* VHT basic MCS set: 0xffea
BSS 3e:b3:01:5d:11:aa(on wlan0)
last seen: 531.154s [boottime]
TSF: 164243763278 usec (1d, 21:37:23)
freq: 5180
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble RadioMeasure (0x1031)
signal: -69.00 dBm
last seen: 5760 ms ago
SSID:
Supported rates: 6.0* 9.0 12.0* 18.0 24.0* 36.0 48.0 54.0
DS Parameter set: channel 36
TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
Country: FR Environment: Indoor/Outdoor
Channels [42 - 54] @ -1 dBm
Power constraint: 0 dB
TPC report: TX power: 63 dBm
Transmit Power Envelope:
* Local Maximum Transmit Power For 20 MHz: 15 dBm
* Local Maximum Transmit Power For 40 MHz: 15 dBm
* Local Maximum Transmit Power For 80 MHz: 15 dBm
RM enabled capabilities:
Capabilities: 0x02 0x00 0x00 0x00 0x00
Neighbor Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
AP Channel Report:
* operating class: 128
* channel(s): 42 58 106 122
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
HT capabilities:
Capabilities: 0x1ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23, 32
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 36
* secondary channel offset: above
* STA channel width: any
* RIFS: 0
* HT protection: 20 MHz
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
VHT capabilities:
VHT Capabilities (0x33c279b1):
Max MPDU length: 7991
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
+HTC-VHT
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 1170 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 1170 Mbps
VHT extended NSS: not supported
VHT operation:
* channel width: 1 (80 MHz)
* center freq segment 1: 42
* center freq segment 2: 0
* VHT basic MCS set: 0xffea
Extended capabilities:
* BSS Transition
* Interworking
* Operating Mode Notification
* Max Number Of MSDUs In A-MSDU is unlimited
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 3
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usec
BSS 3e:b3:01:4d:11:aa(on wlan0)
last seen: 530.537s [boottime]
TSF: 164243149225 usec (1d, 21:37:23)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortPreamble ShortSlotTime RadioMeasure (0x1431)
signal: -67.00 dBm
last seen: 6376 ms ago
SSID:
Supported rates: 1.0* 2.0* 5.5* 11.0* 9.0 18.0 36.0 54.0
DS Parameter set: channel 11
TIM: DTIM Count 0 DTIM Period 1 Bitmap Control 0x0 Bitmap[0] 0x0
Country: FR Environment: Indoor/Outdoor
Channels [1 - 13] @ 20 dBm
Power constraint: 0 dB
TPC report: TX power: 63 dBm
RM enabled capabilities:
Capabilities: 0x02 0x00 0x00 0x00 0x00
Neighbor Report
Nonoperating Channel Max Measurement Duration: 0
Measurement Pilot Capability: 0
AP Channel Report:
* operating class: 81
* channel(s): 1 2 3 4 5 6 7 8 9 10 11 12 13
ERP: Barker_Preamble_Mode
Extended supported rates: 6.0 12.0 24.0 48.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 1-PTKSA-RC 1-GTKSA-RC (0x0000)
BSS Load:
* station count: 5
* channel utilisation: 20/255
* available admission capacity: 31250 [*32us]
HT capabilities:
Capabilities: 0x1ad
RX LDPC
HT20
SM Power Save disabled
RX HT20 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 11
* secondary channel offset: no secondary
* STA channel width: 20 MHz
* RIFS: 0
* HT protection: no
* non-GF present: 1
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
VHT capabilities:
VHT Capabilities (0x33c279b1):
Max MPDU length: 7991
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
+HTC-VHT
RX antenna pattern consistency
TX antenna pattern consistency
VHT RX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 260 Mbps
VHT TX MCS set:
1 streams: MCS 0-8
2 streams: MCS 0-8
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 260 Mbps
VHT extended NSS: not supported
VHT operation:
* channel width: 0 (20 or 40 MHz)
* center freq segment 1: 0
* center freq segment 2: 0
* VHT basic MCS set: 0xffe5
Extended capabilities:
* HT Information Exchange Supported
* BSS Transition
* Interworking
* Max Number Of MSDUs In A-MSDU is unlimited
WMM: * Parameter version 1
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 3
* VI: CW 7-15, AIFSN 2, TXOP 3008 usec
* VO: CW 3-7, AIFSN 2, TXOP 1504 usecHors ligne