Contenu | Rechercher | Menus

Annonce

Si vous avez des soucis pour rester connecté, déconnectez-vous puis reconnectez-vous depuis ce lien en cochant la case
Me connecter automatiquement lors de mes prochaines visites.

À propos de l'équipe du forum.

#1 Le 18/07/2018, à 10:04

bishop

[Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Bonjour,
Jusqu'il y a peu, les ventilateurs de la carte graphique démarraient dès le lancement du système. Depuis une quinzaine de jours ce n'est plus le cas et je dois cocher Enable GPU Fan Settings dans l'interface graphique nvidia-settings => Thermal Settings à chaque démarrage de l'ordi.
Ce problème est apparu alors que j'utilisais le pilote nvidia-driver-390.48 poposé dans les dépôts officiels ubuntu. Pensant que cela pouvait être un bug du pilote après une MAJ j'ai installé le ppa:graphics-drivers/ppa et la version plus récente du pilote 390.77 ce qui n'a pas résolu le problème. J'ai ensuite testé le pilote nvidia-driver-396 (396.24) qui ne change en rien le problème.
On pourrait dire que ça ne coûte pas grand chose de cocher l'option à chaque démarrage mais je ne suis pas le seul à utiliser l'ordi. J'ai mon dernier de 13 ans (le cinquième élément) qui joue régulièrement et qui ne se préoccupe pas particulièrement de la température de la carte et de ce genre de souci.

Donc... si quelqu'un à une solution pour règler ce problème je l'en remercie d'avance.


/etc/X11/xorg.conf généré par nvidia-settings

# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings:  version 396.24  (buildd@lgw01-amd64-037)  Wed May  2 23:26:43 UTC 2018

Section "ServerLayout"
    Identifier     "Layout0"
    Screen      0  "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
    Option         "Xinerama" "0"
EndSection

Section "Files"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
EndSection

Section "Monitor"

    # HorizSync source: edid, VertRefresh source: edid
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "Idek Iiyama PLB2712HDS"
    HorizSync       30.0 - 81.0
    VertRefresh     55.0 - 76.0
    Option         "DPMS"
EndSection

Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce GTX 970"
    Option         "Coolbits" "28"
EndSection

Section "Screen"
    Identifier     "Screen0"
    Device         "Device0"
    Monitor        "Monitor0"
    DefaultDepth    24
    Option         "Stereo" "0"
    Option         "nvidiaXineramaInfoOrder" "DFP-1"
    Option         "metamodes" "nvidia-auto-select +0+0"
    Option         "SLI" "Off"
    Option         "MultiGPU" "Off"
    Option         "BaseMosaic" "off"
    SubSection     "Display"
        Depth       24
    EndSubSection
EndSection

/var/log/Xorg.0.log

[    12.657] (--) Log file renamed from "/var/log/Xorg.pid-1510.log" to "/var/log/Xorg.0.log"
[    12.658] 
X.Org X Server 1.19.6
Release Date: 2017-12-20
[    12.658] X Protocol Version 11, Revision 0
[    12.658] Build Operating System: Linux 4.4.0-119-generic x86_64 Ubuntu
[    12.658] Current Operating System: Linux Ordinosaure 4.15.0-24-generic #26-Ubuntu SMP Wed Jun 13 08:44:47 UTC 2018 x86_64
[    12.658] Kernel command line: BOOT_IMAGE=/vmlinuz-4.15.0-24-generic root=UUID=73b1e498-e918-4be5-8efb-5b54e7221f7d ro quiet splash vt.handoff=1
[    12.658] Build Date: 13 April 2018  08:07:36PM
[    12.658] xorg-server 2:1.19.6-1ubuntu4 (For technical support please see http://www.ubuntu.com/support) 
[    12.658] Current version of pixman: 0.34.0
[    12.658] 	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
[    12.658] Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[    12.658] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Jul 18 10:11:12 2018
[    12.658] (==) Using config file: "/etc/X11/xorg.conf"
[    12.658] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[    12.658] (==) ServerLayout "Layout0"
[    12.658] (**) |-->Screen "Screen0" (0)
[    12.658] (**) |   |-->Monitor "Monitor0"
[    12.658] (**) |   |-->Device "Device0"
[    12.658] (**) |-->Input Device "Keyboard0"
[    12.658] (**) |-->Input Device "Mouse0"
[    12.658] (**) Option "Xinerama" "0"
[    12.658] (==) Automatically adding devices
[    12.658] (==) Automatically enabling devices
[    12.659] (==) Automatically adding GPU devices
[    12.659] (==) Automatically binding GPU devices
[    12.659] (==) Max clients allowed: 256, resource mask: 0x1fffff
[    12.659] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
[    12.659] 	Entry deleted from font path.
[    12.659] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist.
[    12.659] 	Entry deleted from font path.
[    12.659] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist.
[    12.659] 	Entry deleted from font path.
[    12.659] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist.
[    12.659] 	Entry deleted from font path.
[    12.659] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist.
[    12.659] 	Entry deleted from font path.
[    12.659] (==) FontPath set to:
	/usr/share/fonts/X11/misc,
	/usr/share/fonts/X11/Type1,
	built-ins
[    12.659] (==) ModulePath set to "/usr/lib/xorg/modules"
[    12.659] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[    12.659] (WW) Disabling Keyboard0
[    12.659] (WW) Disabling Mouse0
[    12.659] (II) Loader magic: 0x55dbb954e020
[    12.659] (II) Module ABI versions:
[    12.659] 	X.Org ANSI C Emulation: 0.4
[    12.659] 	X.Org Video Driver: 23.0
[    12.659] 	X.Org XInput driver : 24.1
[    12.659] 	X.Org Server Extension : 10.0
[    12.659] (++) using VT number 1

[    12.660] (II) systemd-logind: took control of session /org/freedesktop/login1/session/c2
[    12.660] (II) xfree86: Adding drm device (/dev/dri/card0)
[    12.661] (II) systemd-logind: got fd for /dev/dri/card0 226:0 fd 12 paused 0
[    12.663] (**) OutputClass "nvidia" ModulePath extended to "/usr/lib/x86_64-linux-gnu/nvidia/xorg,/usr/lib/xorg/modules"
[    12.665] (--) PCI:*(0:1:0:0) 10de:13c2:1043:8508 rev 161, Mem @ 0xfa000000/16777216, 0xe0000000/268435456, 0xf0000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/131072
[    12.665] (II) LoadModule: "glx"
[    12.665] (II) Loading /usr/lib/x86_64-linux-gnu/nvidia/xorg/libglx.so
[    12.706] (II) Module glx: vendor="NVIDIA Corporation"
[    12.706] 	compiled for 4.0.2, module version = 1.0.0
[    12.706] 	Module class: X.Org Server Extension
[    12.706] (II) NVIDIA GLX Module  396.24.10  Tue Jul 10 08:21:51 PDT 2018
[    12.707] (II) LoadModule: "nvidia"
[    12.707] (II) Loading /usr/lib/x86_64-linux-gnu/nvidia/xorg/nvidia_drv.so
[    12.707] (II) Module nvidia: vendor="NVIDIA Corporation"
[    12.707] 	compiled for 4.0.2, module version = 1.0.0
[    12.707] 	Module class: X.Org Video Driver
[    12.707] (II) NVIDIA dlloader X Driver  396.24.10  Tue Jul 10 07:58:53 PDT 2018
[    12.707] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[    12.707] (II) systemd-logind: releasing fd for 226:0
[    12.707] (II) Loading sub module "fb"
[    12.707] (II) LoadModule: "fb"
[    12.707] (II) Loading /usr/lib/xorg/modules/libfb.so
[    12.708] (II) Module fb: vendor="X.Org Foundation"
[    12.708] 	compiled for 1.19.6, module version = 1.0.0
[    12.708] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    12.708] (II) Loading sub module "wfb"
[    12.708] (II) LoadModule: "wfb"
[    12.708] (II) Loading /usr/lib/xorg/modules/libwfb.so
[    12.708] (II) Module wfb: vendor="X.Org Foundation"
[    12.708] 	compiled for 1.19.6, module version = 1.0.0
[    12.708] 	ABI class: X.Org ANSI C Emulation, version 0.4
[    12.708] (II) Loading sub module "ramdac"
[    12.708] (II) LoadModule: "ramdac"
[    12.708] (II) Module "ramdac" already built-in
[    12.708] (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32
[    12.708] (==) NVIDIA(0): RGB weight 888
[    12.708] (==) NVIDIA(0): Default visual is TrueColor
[    12.708] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[    12.708] (II) Applying OutputClass "nvidia" options to /dev/dri/card0
[    12.708] (**) NVIDIA(0): Option "Stereo" "0"
[    12.708] (**) NVIDIA(0): Option "nvidiaXineramaInfoOrder" "DFP-1"
[    12.708] (**) NVIDIA(0): Option "SLI" "Off"
[    12.708] (**) NVIDIA(0): Option "MultiGPU" "Off"
[    12.708] (**) NVIDIA(0): Option "BaseMosaic" "off"
[    12.708] (**) NVIDIA(0): Option "AllowEmptyInitialConfiguration"
[    12.708] (**) NVIDIA(0): Stereo disabled by request
[    12.708] (**) NVIDIA(0): NVIDIA SLI disabled.
[    12.708] (**) NVIDIA(0): NVIDIA Multi-GPU disabled.
[    12.708] (**) NVIDIA(0): Option "Coolbits" "28"
[    12.708] (**) NVIDIA(0): Option "MetaModes" "nvidia-auto-select +0+0"
[    12.708] (**) NVIDIA(0): Enabling 2D acceleration
[    13.078] (--) NVIDIA(0): Valid display device(s) on GPU-0 at PCI:1:0:0
[    13.078] (--) NVIDIA(0):     CRT-0
[    13.078] (--) NVIDIA(0):     DFP-0
[    13.078] (--) NVIDIA(0):     DFP-1 (boot)
[    13.078] (--) NVIDIA(0):     DFP-2
[    13.078] (--) NVIDIA(0):     DFP-3
[    13.078] (--) NVIDIA(0):     DFP-4
[    13.079] (II) NVIDIA(0): NVIDIA GPU GeForce GTX 970 (GM204-A) at PCI:1:0:0 (GPU-0)
[    13.079] (--) NVIDIA(0): Memory: 4194304 kBytes
[    13.079] (--) NVIDIA(0): VideoBIOS: 84.04.36.00.5e
[    13.079] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[    13.083] (--) NVIDIA(GPU-0): CRT-0: disconnected
[    13.083] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[    13.083] (--) NVIDIA(GPU-0): 
[    13.086] (--) NVIDIA(GPU-0): DFP-0: disconnected
[    13.086] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[    13.086] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[    13.087] (--) NVIDIA(GPU-0): 
[    13.118] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): connected
[    13.118] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): Internal TMDS
[    13.118] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): 600.0 MHz maximum pixel clock
[    13.118] (--) NVIDIA(GPU-0): 
[    13.118] (--) NVIDIA(GPU-0): DFP-2: disconnected
[    13.118] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[    13.118] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[    13.118] (--) NVIDIA(GPU-0): 
[    13.118] (--) NVIDIA(GPU-0): DFP-3: disconnected
[    13.118] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[    13.118] (--) NVIDIA(GPU-0): DFP-3: 165.0 MHz maximum pixel clock
[    13.118] (--) NVIDIA(GPU-0): 
[    13.118] (--) NVIDIA(GPU-0): DFP-4: disconnected
[    13.118] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[    13.118] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[    13.118] (--) NVIDIA(GPU-0): 
[    13.121] (II) NVIDIA(0): Validated MetaModes:
[    13.121] (II) NVIDIA(0):     "nvidia-auto-select+0+0"
[    13.121] (II) NVIDIA(0): Virtual screen size determined to be 1920 x 1080
[    13.125] (--) NVIDIA(0): DPI set to (81, 80); computed from "UseEdidDpi" X config
[    13.125] (--) NVIDIA(0):     option
[    13.125] (--) Depth 24 pixmap format is 32 bpp
[    13.125] (II) NVIDIA: Using 6144.00 MB of virtual memory for indirect memory
[    13.125] (II) NVIDIA:     access.
[    13.141] (II) NVIDIA(0): Setting mode "nvidia-auto-select+0+0"
[    13.186] (==) NVIDIA(0): Disabling shared memory pixmaps
[    13.186] (==) NVIDIA(0): Backing store enabled
[    13.186] (==) NVIDIA(0): Silken mouse enabled
[    13.186] (**) NVIDIA(0): DPMS enabled
[    13.186] (II) Loading sub module "dri2"
[    13.186] (II) LoadModule: "dri2"
[    13.186] (II) Module "dri2" already built-in
[    13.187] (II) NVIDIA(0): [DRI2] Setup complete
[    13.187] (II) NVIDIA(0): [DRI2]   VDPAU driver: nvidia
[    13.187] (--) RandR disabled
[    13.188] (II) SELinux: Disabled on system
[    13.189] (II) Initializing extension GLX
[    13.189] (II) Indirect GLX disabled.
[    13.222] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[    13.222] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.222] (II) LoadModule: "libinput"
[    13.223] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[    13.223] (II) Module libinput: vendor="X.Org Foundation"
[    13.223] 	compiled for 1.19.6, module version = 0.27.1
[    13.223] 	Module class: X.Org XInput Driver
[    13.223] 	ABI class: X.Org XInput driver, version 24.1
[    13.223] (II) Using input driver 'libinput' for 'Power Button'
[    13.224] (II) systemd-logind: got fd for /dev/input/event1 13:65 fd 39 paused 0
[    13.224] (**) Power Button: always reports core events
[    13.224] (**) Option "Device" "/dev/input/event1"
[    13.224] (**) Option "_source" "server/udev"
[    13.224] (II) event1  - Power Button: is tagged by udev as: Keyboard
[    13.224] (II) event1  - Power Button: device is a keyboard
[    13.224] (II) event1  - Power Button: device removed
[    13.224] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[    13.224] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[    13.224] (**) Option "xkb_model" "pc105"
[    13.224] (**) Option "xkb_layout" "fr"
[    13.234] (II) event1  - Power Button: is tagged by udev as: Keyboard
[    13.234] (II) event1  - Power Button: device is a keyboard
[    13.235] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[    13.235] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[    13.235] (II) Using input driver 'libinput' for 'Power Button'
[    13.235] (II) systemd-logind: got fd for /dev/input/event0 13:64 fd 42 paused 0
[    13.235] (**) Power Button: always reports core events
[    13.235] (**) Option "Device" "/dev/input/event0"
[    13.235] (**) Option "_source" "server/udev"
[    13.235] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    13.235] (II) event0  - Power Button: device is a keyboard
[    13.235] (II) event0  - Power Button: device removed
[    13.235] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[    13.235] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[    13.235] (**) Option "xkb_model" "pc105"
[    13.235] (**) Option "xkb_layout" "fr"
[    13.236] (II) event0  - Power Button: is tagged by udev as: Keyboard
[    13.236] (II) event0  - Power Button: device is a keyboard
[    13.236] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event12)
[    13.236] (II) No input driver specified, ignoring this device.
[    13.236] (II) This device may have been added with another device file.
[    13.236] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event13)
[    13.236] (II) No input driver specified, ignoring this device.
[    13.236] (II) This device may have been added with another device file.
[    13.236] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event14)
[    13.237] (II) No input driver specified, ignoring this device.
[    13.237] (II) This device may have been added with another device file.
[    13.237] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event15)
[    13.237] (II) No input driver specified, ignoring this device.
[    13.237] (II) This device may have been added with another device file.
[    13.237] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event2)
[    13.237] (**) Logitech USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[    13.237] (II) Using input driver 'libinput' for 'Logitech USB Optical Mouse'
[    13.296] (II) systemd-logind: got fd for /dev/input/event2 13:66 fd 43 paused 0
[    13.296] (**) Logitech USB Optical Mouse: always reports core events
[    13.296] (**) Option "Device" "/dev/input/event2"
[    13.296] (**) Option "_source" "server/udev"
[    13.296] (II) event2  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[    13.296] (II) event2  - Logitech USB Optical Mouse: device is a pointer
[    13.296] (II) event2  - Logitech USB Optical Mouse: device removed
[    13.296] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-14/3-14:1.0/0003:046D:C018.0001/input/input2/event2"
[    13.296] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE, id 8)
[    13.296] (**) Option "AccelerationScheme" "none"
[    13.296] (**) Logitech USB Optical Mouse: (accel) selected scheme none/0
[    13.296] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[    13.296] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[    13.297] (II) event2  - Logitech USB Optical Mouse: is tagged by udev as: Mouse
[    13.297] (II) event2  - Logitech USB Optical Mouse: device is a pointer
[    13.297] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[    13.297] (II) No input driver specified, ignoring this device.
[    13.297] (II) This device may have been added with another device file.
[    13.297] (II) config/udev: Adding input device HID 0b38:0010 (/dev/input/event3)
[    13.297] (**) HID 0b38:0010: Applying InputClass "libinput keyboard catchall"
[    13.297] (II) Using input driver 'libinput' for 'HID 0b38:0010'
[    13.298] (II) systemd-logind: got fd for /dev/input/event3 13:67 fd 44 paused 0
[    13.298] (**) HID 0b38:0010: always reports core events
[    13.298] (**) Option "Device" "/dev/input/event3"
[    13.298] (**) Option "_source" "server/udev"
[    13.298] (II) event3  - HID 0b38:0010: is tagged by udev as: Keyboard
[    13.298] (II) event3  - HID 0b38:0010: device is a keyboard
[    13.298] (II) event3  - HID 0b38:0010: device removed
[    13.298] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.3/3-7.3:1.0/0003:0B38:0010.0002/input/input3/event3"
[    13.298] (II) XINPUT: Adding extended input device "HID 0b38:0010" (type: KEYBOARD, id 9)
[    13.298] (**) Option "xkb_model" "pc105"
[    13.298] (**) Option "xkb_layout" "fr"
[    13.299] (II) event3  - HID 0b38:0010: is tagged by udev as: Keyboard
[    13.299] (II) event3  - HID 0b38:0010: device is a keyboard
[    13.299] (II) config/udev: Adding input device HID 0b38:0010 (/dev/input/event4)
[    13.299] (**) HID 0b38:0010: Applying InputClass "libinput keyboard catchall"
[    13.299] (II) Using input driver 'libinput' for 'HID 0b38:0010'
[    13.299] (II) systemd-logind: got fd for /dev/input/event4 13:68 fd 45 paused 0
[    13.299] (**) HID 0b38:0010: always reports core events
[    13.299] (**) Option "Device" "/dev/input/event4"
[    13.299] (**) Option "_source" "server/udev"
[    13.300] (II) event4  - HID 0b38:0010: is tagged by udev as: Keyboard
[    13.300] (II) event4  - HID 0b38:0010: device is a keyboard
[    13.300] (II) event4  - HID 0b38:0010: device removed
[    13.300] (II) libinput: HID 0b38:0010: needs a virtual subdevice
[    13.300] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.3/3-7.3:1.1/0003:0B38:0010.0003/input/input4/event4"
[    13.300] (II) XINPUT: Adding extended input device "HID 0b38:0010" (type: MOUSE, id 10)
[    13.300] (**) Option "AccelerationScheme" "none"
[    13.300] (**) HID 0b38:0010: (accel) selected scheme none/0
[    13.300] (**) HID 0b38:0010: (accel) acceleration factor: 2.000
[    13.300] (**) HID 0b38:0010: (accel) acceleration threshold: 4
[    13.300] (II) event4  - HID 0b38:0010: is tagged by udev as: Keyboard
[    13.300] (II) event4  - HID 0b38:0010: device is a keyboard
[    13.300] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event10)
[    13.301] (II) No input driver specified, ignoring this device.
[    13.301] (II) This device may have been added with another device file.
[    13.301] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event11)
[    13.301] (II) No input driver specified, ignoring this device.
[    13.301] (II) This device may have been added with another device file.
[    13.301] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event5)
[    13.301] (II) No input driver specified, ignoring this device.
[    13.301] (II) This device may have been added with another device file.
[    13.301] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event6)
[    13.301] (II) No input driver specified, ignoring this device.
[    13.301] (II) This device may have been added with another device file.
[    13.301] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event7)
[    13.301] (II) No input driver specified, ignoring this device.
[    13.301] (II) This device may have been added with another device file.
[    13.302] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event8)
[    13.302] (II) No input driver specified, ignoring this device.
[    13.302] (II) This device may have been added with another device file.
[    13.302] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event9)
[    13.302] (II) No input driver specified, ignoring this device.
[    13.302] (II) This device may have been added with another device file.
[    13.305] (**) HID 0b38:0010: Applying InputClass "libinput keyboard catchall"
[    13.305] (II) Using input driver 'libinput' for 'HID 0b38:0010'
[    13.305] (II) systemd-logind: returning pre-existing fd for /dev/input/event4 13:68
[    13.305] (**) HID 0b38:0010: always reports core events
[    13.305] (**) Option "Device" "/dev/input/event4"
[    13.305] (**) Option "_source" "_driver/libinput"
[    13.305] (II) libinput: HID 0b38:0010: is a virtual subdevice
[    13.305] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb3/3-7/3-7.3/3-7.3:1.1/0003:0B38:0010.0003/input/input4/event4"
[    13.305] (II) XINPUT: Adding extended input device "HID 0b38:0010" (type: KEYBOARD, id 11)
[    13.305] (**) Option "xkb_model" "pc105"
[    13.305] (**) Option "xkb_layout" "fr"
[    13.449] (--) NVIDIA(GPU-0): CRT-0: disconnected
[    13.449] (--) NVIDIA(GPU-0): CRT-0: 400.0 MHz maximum pixel clock
[    13.449] (--) NVIDIA(GPU-0): 
[    13.453] (--) NVIDIA(GPU-0): DFP-0: disconnected
[    13.453] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[    13.453] (--) NVIDIA(GPU-0): DFP-0: 330.0 MHz maximum pixel clock
[    13.453] (--) NVIDIA(GPU-0): 
[    13.484] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): connected
[    13.484] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): Internal TMDS
[    13.484] (--) NVIDIA(GPU-0): Idek Iiyama PLB2712HDS (DFP-1): 600.0 MHz maximum pixel clock
[    13.484] (--) NVIDIA(GPU-0): 
[    13.484] (--) NVIDIA(GPU-0): DFP-2: disconnected
[    13.484] (--) NVIDIA(GPU-0): DFP-2: Internal DisplayPort
[    13.484] (--) NVIDIA(GPU-0): DFP-2: 960.0 MHz maximum pixel clock
[    13.484] (--) NVIDIA(GPU-0): 
[    13.484] (--) NVIDIA(GPU-0): DFP-3: disconnected
[    13.484] (--) NVIDIA(GPU-0): DFP-3: Internal TMDS
[    13.484] (--) NVIDIA(GPU-0): DFP-3: 165.0 MHz maximum pixel clock
[    13.484] (--) NVIDIA(GPU-0): 
[    13.484] (--) NVIDIA(GPU-0): DFP-4: disconnected
[    13.484] (--) NVIDIA(GPU-0): DFP-4: Internal TMDS
[    13.484] (--) NVIDIA(GPU-0): DFP-4: 330.0 MHz maximum pixel clock
[    13.484] (--) NVIDIA(GPU-0): 
[   139.246] (**) Option "fd" "39"
[   139.246] (II) event1  - Power Button: device removed
[   139.246] (**) Option "fd" "42"
[   139.246] (II) event0  - Power Button: device removed
[   139.247] (**) Option "fd" "43"
[   139.247] (II) event2  - Logitech USB Optical Mouse: device removed
[   139.247] (**) Option "fd" "44"
[   139.247] (II) event3  - HID 0b38:0010: device removed
[   139.247] (**) Option "fd" "45"
[   139.247] (**) Option "fd" "45"
[   139.247] (II) event4  - HID 0b38:0010: device removed
[   139.351] (II) systemd-logind: got pause for 13:68
[   139.351] (II) systemd-logind: got pause for 13:65
[   139.351] (II) systemd-logind: got pause for 13:66
[   139.351] (II) systemd-logind: got pause for 13:64
[   139.351] (II) systemd-logind: got pause for 13:67

Dernière modification par bishop (Le 23/07/2018, à 02:14)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#2 Le 18/07/2018, à 12:38

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Salut,

Je soupçonne que ça soit l'option "Coolbits" dans ton xorg.conf qui ne soit pas à la bonne valeur.
Tu peux essayer de passer à 4 au lieu de 28

sudo nvidia-xconfig --cool-bits=4

La case restera décochée, mais la vitesse du ventilo sera gérée automatiquement. Si la case est cochée, tu peux règler la vitesse manuellement.

Edit: la valeur par défaut est 0 (tout en auto, et la case disparaît)

Dernière modification par Gaara (Le 18/07/2018, à 12:43)


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#3 Le 18/07/2018, à 17:40

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Salut Gaara,
et Merci pour ton intervention.

J'ai fait ce que tu conseilles mais ça ne change rien. Mais... car il y a souvent un mais, je ne sais pas comment sont gérés les ventilos de la carte graphique et à quelle température ils se déclenchent. Dans la DOC. de la carte il est dit :

Cette carte graphique équipée du système de refroidissement STRIX ASUS peut fonctionner en mode fanless (ventilateurs coupés) si la charge de la carte graphique est faible.

Je ferai un test sans cocher Enable GPU Fan Settings avec quelques outils permettant de stresser le GPU pour voir si les ventilos se déclenchent et à quelle température.

Dernière modification par bishop (Le 18/07/2018, à 21:16)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#4 Le 19/07/2018, à 06:09

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

bishop a écrit :

Je ferai un test sans cocher Enable GPU Fan Settings avec quelques outils permettant de stresser le GPU pour voir si les ventilos se déclenchent et à quelle température.

cool-bits=4
À 62° les ventilos ne tournent toujours pas.

Dernière modification par bishop (Le 19/07/2018, à 06:11)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#5 Le 19/07/2018, à 08:40

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

En effet c'est pas normal... C'est quoi le modèle précis de ta carte ?

Après quelques recherches, j'ai trouvé ceci: https://bbs.archlinux.org/viewtopic.php?id=201124
Donc ça serait l'option GPUFanControlState qui serait à 0 au lieu d'être à 1.

Dernière modification par Gaara (Le 19/07/2018, à 08:55)


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#6 Le 19/07/2018, à 08:54

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Gaara a écrit :

En effet c'est pas normal... C'est quoi le modèle précis de ta carte ?

Carte graphique Asus GeForce GTX 970 STRIX OC - 4 Go achetée le 18/05/2016 chez M...net.


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#7 Le 19/07/2018, à 08:56

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Peux tu donner le retour de

nvidia-settings -q all | grep Fan

(j'ai édité mon message précédant)


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#8 Le 19/07/2018, à 09:07

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Et la commande pour cocher la case à 35% (par exemple) est

nvidia-settings -a "[gpu:0]/GPUFanControlState=1" -a "[fan:0]/GPUCurrentFanSpeed=35"

Dernière modification par Gaara (Le 19/07/2018, à 09:08)


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#9 Le 19/07/2018, à 09:28

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Gaara a écrit :

Peux tu donner le retour de

nvidia-settings -q all | grep Fan

(j'ai édité mon message précédant)

bishop@Ordinosaure:~$ nvidia-settings -q all | grep Fan
  Attribute 'GPUFanControlState' (Ordinosaure:1[gpu:0]): 1.
    'GPUFanControlState' is a boolean attribute; valid values are: 1 (on/true)
    'GPUFanControlState' can use the following target types: GPU.
  Attribute 'GPUTargetFanSpeed' (Ordinosaure:1[fan:0]): 50.
    The valid values for 'GPUTargetFanSpeed' are in the range 0 - 100
    'GPUTargetFanSpeed' can use the following target types: Fan.
  Attribute 'GPUCurrentFanSpeed' (Ordinosaure:1[fan:0]): 50.
    The valid values for 'GPUCurrentFanSpeed' are in the range 0 - 100
    'GPUCurrentFanSpeed' is a read-only attribute.
    'GPUCurrentFanSpeed' can use the following target types: Fan.
  Attribute 'GPUCurrentFanSpeedRPM' (Ordinosaure:1[fan:0]): 1523.
    'GPUCurrentFanSpeedRPM' is an integer attribute.
    'GPUCurrentFanSpeedRPM' is a read-only attribute.
    'GPUCurrentFanSpeedRPM' can use the following target types: Fan.
  Attribute 'GPUFanControlType' (Ordinosaure:1[fan:0]): 2.
    'GPUFanControlType' is an integer attribute.
    'GPUFanControlType' is a read-only attribute.
    'GPUFanControlType' can use the following target types: Fan.
  Attribute 'GPUFanTarget' (Ordinosaure:1[fan:0]): 0x00000007.
    'GPUFanTarget' is a bitmask attribute.
    'GPUFanTarget' is a read-only attribute.
    'GPUFanTarget' can use the following target types: Fan.

[Edit] Enable GPU Fan Settings est coché.

Dernière modification par bishop (Le 19/07/2018, à 09:35)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#10 Le 19/07/2018, à 09:46

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Le retour indique que tu as réglé la vitesse à 50%, et que le ventilo tourne. C'est ça?

Si j'ai compris les commandes,

nvidia-settings -a "[gpu:0]/GPUFanControlState=0"

décoche la case (et la vitesse devrait être automatique selon la température du GPU), et

nvidia-settings -a "[gpu:0]/GPUFanControlState=1" -a "[fan:0]/GPUCurrentFanSpeed=35"

Coche la case avec une vitesse manuelle de 35%.

Donc si ça ne marche pas en auto, il faudrait écrire un petit script lancé par un cron toutes les minutes, qui vérifie la température (via nvidia-settings -q all | grep Temp) et qui modifie la vitesse manuelle en fonction.
J'avoue c'est du bricolage, mais ça pourrait marcher !


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#11 Le 19/07/2018, à 10:08

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Merci Gaara.
Je vais voir tout cela.

Je teste un p'tit outil que j'ai trouver : GUI nVidia fan control

1531990760.png


Je dois m'absenter, à mon retour je testerai la commande :

nvidia-settings -a "[gpu:0]/GPUFanControlState=1" -a "[fan:0]/GPUCurrentFanSpeed=50"

pour voir si la vitesse des ventilos à 50% est suffisante pour refroidir la carte quand elle est fortement sollicitée.


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#12 Le 20/07/2018, à 10:22

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Salut Gaara,
Peux-tu me dire dans quel fichier sont enregistrées les infos GPUFanControlState, GPUCurrentFanSpeed et autres.
Merci.


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#13 Le 20/07/2018, à 10:24

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Gaara a écrit :

Le retour indique que tu as réglé la vitesse à 50%, et que le ventilo tourne. C'est ça?

J'avais pas répondu à ta question mais c'est bien ça.


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#14 Le 20/07/2018, à 10:52

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Salut bishop,

Tu devrais trouver des infos ici: https://download.nvidia.com/XFree86/Lin … -guide.txt
Apparemment tu peux ajouter une ligne dans le fichier /etc/X11/xinit/xinitrc


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#15 Le 20/07/2018, à 14:11

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Merci pour les infos.
Dans le NVIDIA-SETTINGS USER GUIDE il est fait référence au fichier .nvidia-settings-rc.
Voila le mien, généré par nvidia-settings :

#
# /home/bishop/.nvidia-settings-rc
#
# Configuration file for nvidia-settings - the NVIDIA X Server Settings utility
# Generated on Fri Jul 20 14:54:10 2018
#

# ConfigProperties:

RcFileLocale = C
DisplayStatusBar = Yes
SliderTextEntries = Yes
IncludeDisplayNameInConfigFile = No
ShowQuitDialog = Yes
UpdateRulesOnProfileNameChange = Yes
Timer = Memory_Used_(GPU_0),Yes,3000
Timer = Thermal_Monitor_(GPU_0),Yes,1000
Timer = PowerMizer_Monitor_(GPU_0),Yes,1000

# Attributes:

0/SyncToVBlank=1
0/LogAniso=0
0/FSAA=0
0/TextureClamping=1
0/FXAA=0
0/AllowFlipping=1
0/FSAAAppControlled=1
0/LogAnisoAppControlled=1
0/OpenGLImageSettings=1
0/FSAAAppEnhanced=0
[DPY:DVI-I-0]/Dithering=0
[DPY:DVI-I-0]/DitheringMode=0
[DPY:DVI-I-0]/DitheringDepth=0
[DPY:DVI-I-0]/SynchronousPaletteUpdates=0
[DPY:DVI-I-1]/Dithering=0
[DPY:DVI-I-1]/DitheringMode=0
[DPY:DVI-I-1]/DitheringDepth=0
[DPY:DVI-I-1]/ColorSpace=0
[DPY:DVI-I-1]/ColorRange=0
[DPY:DVI-I-1]/SynchronousPaletteUpdates=0
[DPY:HDMI-0]/RedBrightness=0.000000
[DPY:HDMI-0]/GreenBrightness=0.000000
[DPY:HDMI-0]/BlueBrightness=0.000000
[DPY:HDMI-0]/RedContrast=0.000000
[DPY:HDMI-0]/GreenContrast=0.000000
[DPY:HDMI-0]/BlueContrast=0.000000
[DPY:HDMI-0]/RedGamma=1.000000
[DPY:HDMI-0]/GreenGamma=1.000000
[DPY:HDMI-0]/BlueGamma=1.000000
[DPY:HDMI-0]/Dithering=0
[DPY:HDMI-0]/DitheringMode=0
[DPY:HDMI-0]/DitheringDepth=0
[DPY:HDMI-0]/DigitalVibrance=0
[DPY:HDMI-0]/ColorSpace=0
[DPY:HDMI-0]/ColorRange=0
[DPY:HDMI-0]/SynchronousPaletteUpdates=0
[DPY:DP-0]/Dithering=0
[DPY:DP-0]/DitheringMode=0
[DPY:DP-0]/DitheringDepth=0
[DPY:DP-0]/ColorSpace=0
[DPY:DP-0]/ColorRange=0
[DPY:DP-0]/SynchronousPaletteUpdates=0
[DPY:DP-1]/Dithering=0
[DPY:DP-1]/DitheringMode=0
[DPY:DP-1]/DitheringDepth=0
[DPY:DP-1]/ColorSpace=0
[DPY:DP-1]/ColorRange=0
[DPY:DP-1]/SynchronousPaletteUpdates=0
[DPY:DVI-D-0]/Dithering=0
[DPY:DVI-D-0]/DitheringMode=0
[DPY:DVI-D-0]/DitheringDepth=0
[DPY:DVI-D-0]/ColorSpace=0
[DPY:DVI-D-0]/ColorRange=0
[DPY:DVI-D-0]/SynchronousPaletteUpdates=0

À part la ligne (en gras) :

Timer = Thermal_Monitor_(GPU_0),Yes,1000

il n'y a pas d'autres références à la gestion de la température et aucunes aux ventilateurs.


Donc... qu'est-ce que ça pourrait changer de faire référence au fichier .nvidia-settings-rc dans /etc/X11/xinit/xinitrc (référence : 4.  Loading Settings Automatically) pour le chargement automatique des paramètres ?


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#16 Le 20/07/2018, à 15:19

Gaara

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Bonne question... Je ne sais pas du tout !
Ce que j'ai compris, c'est que si tu ajoutes

nvidia-settings -a "[gpu:0]/GPUFanControlState=1" -a "[fan:0]/GPUCurrentFanSpeed=50"

au fichier /etc/X11/xinit/xinitrc, avant la ligne

. /etc/X11/Xsession

cela sera chargé au démarrage, à l'initialisation du driver. Pour le reste, je ne comprend pas non plus ou pourraient être les autres paramètres, ou comment ils sont attribués


Kubuntu 18.04 x64
Un terminal tactile Raspberry Pi et Odroid

                                        <code>zenity  --question --title "Alert"  --text "Microsoft Windows has been found! Would you like to remove it?"</code>

Hors ligne

#17 Le 20/07/2018, à 17:16

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

Gaara a écrit :

... ... ...
... Pour le reste, je ne comprend pas non plus ou pourraient être les autres paramètres, ou comment ils sont attribués

Il y a bien le dossier caché ~/.nv contenant les dossiers ComputeCache et GLCache, mais leur contenu est crypté et donc inaccessible.
Logiciel privatif... quand tu nous tiens. mad


Note.
J'ai testé le p'tit soft NVIDIA GPU Fan Control qui fonctionne plutôt pas mal. Maintenant je voudrais le lancer au démarrage mais sans l'interface graphique. Mais là je sèche.
J'ai parcouru le fichier gpufancnv.pyw pour voir de quoi il retournait mais ça ne m'apporte rien. Je n'y connais rien en python. Il y a quand même une référence à l'attribut "GPUTargetFanSpeed" utilisé pour la gestion des ventilos.

# Newer NVIDIA drivers use the "GPUTargetFanSpeed" attribute

Dernière modification par bishop (Le 20/07/2018, à 17:18)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne

#18 Le 23/07/2018, à 02:11

bishop

Re : [Contourné] NVIDIA Obligé de cocher Enable GPU Fan à chaque démarrage

J'ai cherché un démon qui lancerait un script permettant la gestion de la vitesse des ventilos en fonction de la température du GPU, comme le fait NVIDIA GPU Fan Control.

Il y a bien quelques scripts qui sont généralement dédiés aux Multi-GPU mais toujours avec une seule ligne pour la vitesse des ventilos :

nvidia-settings -a "[gpu:0]/GPUFanControlState=1" -a "[fan:0]/GPUCurrentFanSpeed=x"

Pour l'instant j'utilise le NVIDIA GPU Fan Control. Pour que mon gamin n'oublie pas de le lancer quand il joue, j'ai créé un lanceur placé sur le bureau et ainsi faciliter son lancement.
Je passe la discussion en [Contourné] et je verrai, à l'occasion, si je trouve quelque chose.

Merci Gaara pour tes interventions. smile

Dernière modification par bishop (Le 23/07/2018, à 16:15)


La plus grande surprise que puisse faire un con c'est de faire une pause.

Hors ligne