#26 Le 16/02/2023, à 08:05
- Zion
Re : Ubuntu est long au démarrage [HELP]
Up !
Hors ligne
#27 Le 16/02/2023, à 09:52
- geole
Re : Ubuntu est long au démarrage [HELP]
Bonjour
J'attendais la suite des informations pour tenter de trouver une ou des causes.
Avec ce que tu as posté, le disque est en bon état et tourne a bonne vitesse et la partie utilisateur met en route en 1min 56.390s. Cela semble effectivement un peu long.
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#28 Le 16/02/2023, à 10:08
- Zion
Re : Ubuntu est long au démarrage [HELP]
Bonjour geole, merci.
Que te manque-t-il ?
Bonne journée !
Hors ligne
#29 Le 16/02/2023, à 11:25
- geole
Re : Ubuntu est long au démarrage [HELP]
Refais la totalité de ces commandes afin d avoir un instantané.
Pour les temps de démarrage, on va refaire un point.
systemd-analyze time && systemd-analyze --user
systemd-analyze blame | head -25
systemd-analyze critical-chain
journalctl -b --no-pager -p err
ls -l /var/crash
echo $XDG_SESSION_TYPE && journalctl -b --no-pager -g BOOT_IMAGE
sudo smartctl -a /dev/sda
et tu donnes une réponse par commande incluant la commande.
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#30 Le 16/02/2023, à 18:47
- Zion
Re : Ubuntu est long au démarrage [HELP]
Très bien !
Startup finished in 4.186s (kernel) + 2min 2.343s (userspace) = 2min 6.530s
graphical.target reached after 1min 59.858s in userspace.
Startup finished in 14.364s (userspace)
default.target reached after 13.379s in userspace.
1min 3.971s plymouth-quit-wait.service
30.350s systemd-journal-flush.service
25.537s snapd.service
22.367s apport-autoreport.service
19.678s dev-sda5.device
14.516s udisks2.service
14.296s fwupd.service
12.768s dev-loop39.device
12.544s iio-sensor-proxy.service
12.524s dev-loop37.device
12.475s accounts-daemon.service
12.472s dev-loop38.device
12.226s dev-loop40.device
12.215s power-profiles-daemon.service
12.211s dev-loop27.device
12.208s dev-loop25.device
12.205s dev-loop30.device
12.028s dev-loop21.device
12.025s dev-loop31.device
11.982s polkit.service
11.029s dev-loop12.device
11.000s dev-loop32.device
10.961s dev-loop33.device
10.925s dev-loop34.device
10.817s avahi-daemon.service
The time when unit became active or started is printed after the "@" character.
The time the unit took to start is printed after the "+" character.
graphical.target @1min 59.858s
└─multi-user.target @1min 59.858s
└─plymouth-quit-wait.service @55.885s +1min 3.971s
└─systemd-user-sessions.service @55.703s +179ms
└─network.target @55.472s
└─NetworkManager.service @48.396s +7.075s
└─dbus.service @37.585s +10.804s
└─basic.target @37.530s
└─sockets.target @37.530s
└─snapd.socket @37.522s +8ms
└─sysinit.target @37.457s
└─systemd-resolved.service @36.800s +655ms
└─systemd-tmpfiles-setup.service @35.836s +922ms
└─systemd-journal-flush.service @5.484s +30.350s
└─systemd-remount-fs.service @5.309s +173ms
└─systemd-journald.socket @5.029s
└─system.slice @5.014s
└─-.slice @5.014s
févr. 16 17:31:48 x kernel: ERROR: Unable to locate IOAPIC for GSI 37
févr. 16 17:31:48 x kernel: ERROR: Unable to locate IOAPIC for GSI 38
févr. 16 17:32:18 x kernel: Bluetooth: hci0: unexpected event for opcode 0x0000
févr. 16 17:32:20 x systemd[1]: apt-daily.timer: Refusing to start, unit apt-daily.service to trigger not loaded.
févr. 16 17:32:20 x systemd[1]: Failed to start Daily apt download activities.
févr. 16 17:32:35 x bluetoothd[1144]: src/device.c:set_wake_allowed_complete() Set device flags return status: Invalid Parameters
févr. 16 17:32:35 x bluetoothd[1144]: src/adapter.c:set_device_privacy_complete() Set device flags return status: Invalid Parameters
févr. 16 17:32:53 x canonical-livepatch.canonical-livepatchd[1341]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:53 x canonical-livepatch.canonical-livepatchd[1593]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:53 x canonical-livepatch.canonical-livepatchd[1623]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:53 x canonical-livepatch.canonical-livepatchd[1656]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:54 x canonical-livepatch.canonical-livepatchd[1685]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:54 x canonical-livepatch.canonical-livepatchd[1719]: The platform Ubuntu 22.10 is not supported. exiting.
févr. 16 17:32:54 x systemd[1]: Failed to start Service for snap application canonical-livepatch.canonical-livepatchd.
févr. 16 17:33:20 x bluetoothd[1144]: src/profile.c:record_cb() Unable to get Hands-Free Voice gateway SDP record: Host is down
févr. 16 17:33:25 x bluetoothd[1144]: src/profile.c:record_cb() Unable to get Hands-Free Voice gateway SDP record: Host is down
févr. 16 17:36:16 x gdm-password][2481]: gkr-pam: unable to locate daemon control file
févr. 16 17:36:26 x bluetoothd[1144]: src/profile.c:record_cb() Unable to get Hands-Free Voice gateway SDP record: Host is down
févr. 16 17:36:31 x bluetoothd[1144]: src/profile.c:record_cb() Unable to get Hands-Free Voice gateway SDP record: Host is down
févr. 16 17:36:27 x systemd[2493]: Failed to start Application launched by gnome-session-binary.
févr. 16 17:36:34 x gdm-launch-environment][1379]: GLib-GObject: g_object_unref: assertion 'G_IS_OBJECT (object)' failed
total 0
echo $XDG_SESSION_TYPE && journalctl -b --no-pager -g BOOT_IMAGE
wayland
févr. 16 17:31:48 x kernel: Command line: BOOT_IMAGE=/boot/vmlinuz-5.19.0-31-generic root=UUID=0a2a8555-f07e-40a2-8a14-26538dfac12d ro quiet splash vt.handoff=7
févr. 16 17:31:48 x kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-5.19.0-31-generic root=UUID=0a2a8555-f07e-40a2-8a14-26538dfac12d ro quiet splash vt.handoff=7
févr. 16 17:31:48 x kernel: Unknown kernel command line parameters "splash BOOT_IMAGE=/boot/vmlinuz-5.19.0-31-generic", will be passed to user space.
févr. 16 17:31:48 x kernel: BOOT_IMAGE=/boot/vmlinuz-5.19.0-31-generic
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-5.19.0-31-generic] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HTS723232A7A364
Serial Number: E3834523G4JG6N
LU WWN Device Id: 5 000cca 6d5c20f44
Firmware Version: EC2OA60W
User Capacity: 320072933376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database 7.3/5319
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Feb 16 17:46:48 2023 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 76) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 094 062 Pre-fail Always - 0
2 Throughput_Performance 0x0025 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0023 253 100 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 3452
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 070 070 000 Old_age Always - 13267
10 Spin_Retry_Count 0x0033 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 2686
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 124557524992
188 Command_Timeout 0x0032 100 091 000 Old_age Always - 4307
190 Airflow_Temperature_Cel 0x0022 067 043 045 Old_age Always In_the_past 33 (Min/Max 23/33)
191 G-Sense_Error_Rate 0x0032 086 086 000 Old_age Always - 3732
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 10616994
193 Load_Cycle_Count 0x0032 036 036 000 Old_age Always - 643793
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 0
223 Load_Retry_Count 0x002a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 occurred at disk power-on lifetime: 12677 hours (528 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 00 60 1b 8a 02 Error: IDNF at LBA = 0x028a1b60 = 42605408
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 18 20 00 15 5f 40 00 00:18:49.216 WRITE FPDMA QUEUED
60 80 18 90 9f 0f 40 00 00:18:45.283 READ FPDMA QUEUED
61 08 10 c0 5e c0 40 00 00:18:41.963 WRITE FPDMA QUEUED
61 00 08 c0 5d c0 40 00 00:18:41.963 WRITE FPDMA QUEUED
61 08 00 d0 29 12 40 00 00:18:41.832 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Hors ligne
#31 Le 16/02/2023, à 19:10
- xubu1957
Re : Ubuntu est long au démarrage [HELP]
Bonjour,
et tu donnes une réponse par commande incluant la commande.
Un retour complet doit contenir toutes les lignes,
depuis celle, entière, de la commande
jusqu'à la ligne attendant la commande suivante, exemple :moi@mon-pc~$: ma-commande son retour moi@mon-pc~$:
Faute de quoi, il manque souvent à ceux qui tentent de t'aider des éléments essentiels.
(Plus de détails dans ce message-ci Retour utilisable de commande.)
Et si tu ne veux pas divulguer ton nom d'user, tu le remplaces par "toto" ou ce que tu veux.
Lecture conseillée > memento des balises code.
Montre la RAM :
LANG=C free -wh
et :
df -Th
Dernière modification par xubu1957 (Le 16/02/2023, à 19:14)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#32 Le 16/02/2023, à 19:18
- geole
Re : Ubuntu est long au démarrage [HELP]
C'est bien d'avoir un ensemble cohérent.
Je ne sais pas comment chercher. De façon logique en demandant à plymouth pourquoi il est si lent!
https://askubuntu.com/questions/1119167 … untu-18-04
systemctl --no-pager list-dependencies plymouth-quit-wait.service
mais cela ne liste pas le temps de chaque service.
il faut alors faire cette commande
systemd-analyze plot > ~/SystemdAnalyzePlot.svg
puis consulter le fichier
eog SystemdAnalyzePlot.svg
Mais je me demande comment on peut faire pour lire avec des caractères si petits.
Avec gimp, j'arrive à faire des agrandissements lisibles.
Le fichier n'a pas l'air gros, si tu peux le mettre à disposition dans un site de partage....
De façon empirique en regardant les détails de la trace dans le créneau.
journalctl --since "2023-02-16 17:32:43" --until "2023-02-16 17:34:48" >Trace.txt && xdg-open Trace.txt
Pour rechercher les deux erreurs APIC, donne ce retour
cat /proc/interrupts
Dernière modification par geole (Le 16/02/2023, à 19:33)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#33 Le 16/02/2023, à 19:22
- xubu1957
Re : Ubuntu est long au démarrage [HELP]
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#34 Le 16/02/2023, à 21:56
- ylag
Re : Ubuntu est long au démarrage [HELP]
Bonsoir,
Mais je me demande comment on peut faire pour lire avec des caractères si petits.
L'affichage de ce genre de fichier se gère bien dans un navigateur web ...
A+
Dernière modification par ylag (Le 16/02/2023, à 21:57)
Hors ligne
#35 Le 17/02/2023, à 02:50
- Zion
Re : Ubuntu est long au démarrage [HELP]
(IOAPIC)
niko@x:~$ cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
0: 9 0 0 0 IR-IO-APIC 2-edge timer
1: 0 0 50 0 IR-IO-APIC 1-edge i8042
8: 0 0 0 1 IR-IO-APIC 8-edge rtc0
9: 0 1250 0 0 IR-IO-APIC 9-fasteoi acpi
12: 0 321 0 0 IR-IO-APIC 12-edge i8042
16: 0 0 0 31 IR-IO-APIC 16-fasteoi ehci_hcd:usb1
18: 13215 0 0 1303 IR-IO-APIC 18-fasteoi i801_smbus
19: 0 0 0 17 IR-IO-APIC 19-fasteoi
21: 35 0 0 0 IR-IO-APIC 21-fasteoi ehci_hcd:usb2
23: 0 0 0 0 IR-IO-APIC 23-edge smo8800
24: 0 0 0 0 DMAR-MSI 0-edge dmar0
25: 0 0 0 0 DMAR-MSI 1-edge dmar1
33: 5951 0 0 2412 IR-PCI-MSI 327680-edge xhci_hcd
34: 0 67298 0 0 IR-PCI-MSI 512000-edge ahci[0000:00:1f.2]
35: 46 0 0 6 IR-PCI-MSI 409600-edge eno1
36: 0 0 0 0 IR-PCI-MSI 7340032-edge mmc0
37: 0 0 44 0 IR-PCI-MSI 360448-edge mei_me
38: 0 0 0 24740 IR-PCI-MSI 1572864-edge iwlwifi
39: 148 0 13179 0 IR-PCI-MSI 32768-edge i915
40: 0 274 0 0 IR-PCI-MSI 49152-edge snd_hda_intel:card0
41: 0 0 513 0 IR-PCI-MSI 442368-edge snd_hda_intel:card1
NMI: 0 0 0 0 Non-maskable interrupts
LOC: 94538 96912 92835 95407 Local timer interrupts
SPU: 0 0 0 0 Spurious interrupts
PMI: 0 0 0 0 Performance monitoring interrupts
IWI: 1020 848 8633 981 IRQ work interrupts
RTR: 0 0 0 0 APIC ICR read retries
RES: 3049 2787 3121 2916 Rescheduling interrupts
CAL: 34719 32351 26393 28474 Function call interrupts
TLB: 8746 9948 6362 9651 TLB shootdowns
TRM: 0 0 0 0 Thermal event interrupts
THR: 0 0 0 0 Threshold APIC interrupts
DFR: 0 0 0 0 Deferred Error APIC interrupts
MCE: 0 0 0 0 Machine check exceptions
MCP: 4 5 5 5 Machine check polls
ERR: 0
MIS: 0
PIN: 0 0 0 0 Posted-interrupt notification event
NPI: 0 0 0 0 Nested posted-interrupt event
PIW: 0 0 0 0 Posted-interrupt wakeup event
niko@x:~$
-------
Dernière modification par Zion (Le 17/02/2023, à 02:52)
Hors ligne
#36 Le 17/02/2023, à 14:10
- geole
Re : Ubuntu est long au démarrage [HELP]
Bonjour.
J'ai parcouru la trace jusqu'à la lecture de cette ligne
févr. 16 17:33:45 x systemd[1]: Startup finished in 4.186s (kernel) + 2min 2.343s (userspace) = 2min 6.530s.
Sans trouver une ligne expliquant une lenteur
J'ai relevé
févr. 16 17:32:53 x systemd[1]: snap.canonical-livepatch.canonical-livepatchd.service: Main process exited, code=exited, status=1/FAILURE
févr. 16 17:32:54 x canonical-livepatch.canonical-livepatchd[1719]: The platform Ubuntu 22.10 is not supported. exiting.
C'est bête de lancer un service qui n'est pas supporté. Le coût: 1 seconde ?
févr. 16 17:33:00 x systemd[1409]: snap.snapd-desktop-integration.snapd-desktop-integration.service: Main process exited, code=exited, status=1/FAILURE
févr. 16 17:33:00 x systemd[1409]: snap.snapd-desktop-integration.snapd-desktop-integration.service: Failed with result 'exit-code'.
La cause du plantage me semble assez obscure.....
Pour ces avertissements
févr. 16 17:31:48 x kernel: ERROR: Unable to locate IOAPIC for GSI 37
févr. 16 17:31:48 x kernel: ERROR: Unable to locate IOAPIC for GSI 38
Je les relie à
niko@x:~$ cat /proc/interrupts
CPU0 CPU1 CPU2 CPU3
37: 0 0 44 0 IR-PCI-MSI 360448-edge mei_me
38: 0 0 0 24740 IR-PCI-MSI 1572864-edge iwlwifi
As-tu un problème wifi?. Je sèche pour mei-me
A mon avis, te temps de démarrage semble normal.
Dernière modification par geole (Le 17/02/2023, à 14:24)
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne
#37 Le 17/02/2023, à 14:39
- xubu1957
Re : Ubuntu est long au démarrage [HELP]
Bonjour,
@geole
Pour info > linuxfr.org/forums/linux-general/posts/resolu-mei_me-reached-maximal-consecutive-resets-disabling-the-device
Et un boot-info.
Dernière modification par xubu1957 (Le 17/02/2023, à 14:45)
Conseils pour les nouveaux demandeurs et pas qu'eux
Important : Pensez à passer vos sujets en [Résolu] lorsque ceux-ci le sont, au début du titre en cliquant sur Modifier sous le premier message, et un bref récapitulatif de la solution à la fin de celui-ci. Merci. Membre de Linux-Azur
Hors ligne
#38 Le 17/02/2023, à 15:01
- Zion
Re : Ubuntu est long au démarrage [HELP]
Démarrage : ok, ça a l'air d'aller.
Mais j'aimerai résoudre le problème IOAPIC
et le problème F12 au démarrage pour lancer Windows Boot Manager alors qu'en fait c'est Ubuntu.
J'y comprends pas grand chose, désolé.
Hors ligne
#39 Le 17/02/2023, à 20:48
- geole
Re : Ubuntu est long au démarrage [HELP]
et le problème F12 au démarrage pour lancer Windows Boot Manager alors qu'en fait c'est Ubuntu.
Comme l'autre discussion n'est pas fermée, autant l'utiliser.
Les grilles de l'installateur https://doc.ubuntu-fr.org/tutoriel/inst … _subiquity
"gedit admin:///etc/fstab" est proscrit, utilisez "pkexec env DISPLAY=$DISPLAY XAUTHORITY=$XAUTHORITY xdg-open /etc/fstab" Voir https://doc.ubuntu-fr.org/gedit
Les partitions EXT4 des disques externes => https://forum.ubuntu-fr.org/viewtopic.p … #p22697248
Hors ligne