Pages : 1
#1 Le 03/06/2018, à 14:36
- theyellow29
Erreur SMART
Bonjour,
Depuis un moment l’accès à mon second DD (Seagate Barracuda 1 To) est long via Nautilus.
J'ai testé le DD avec gnome-disk-utility pour visualier les données SMART .
https://zupimages.net/up/18/22/uecv.png
Parement j'ai une partie du DD qui doit être endommagé. J'ai lancé un auto-test il resté bloqué à 90%
J'ai installé GSmartControl pour avoir plus d'information et c'est complètement plus abstrait pour moi.
Donc je voudrais savoir si c'est grave pour envisager l’achat d'un autre DD ou je peut le laisser dans cet état.
Merci
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-22-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.14 (AF) Device Model: ST1000DM003-1ER162 Serial Number: Z4Y6DYKE LU WWN Device Id: 5 000c50 07aee4be5 Firmware Version: CC45 User Capacity: 1000204886016 bytes [1,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sun Jun 3 13:51:38 2018 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM level is: 254 (maximum performance) Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 80) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 106) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x1085) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 104 099 006 - 146358490 3 Spin_Up_Time PO---- 097 097 000 - 0 4 Start_Stop_Count -O--CK 096 096 020 - 4227 5 Reallocated_Sector_Ct PO--CK 099 099 010 - 640 7 Seek_Error_Rate POSR-- 069 060 030 - 7980609 9 Power_On_Hours -O--CK 093 093 000 - 6445 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 096 096 020 - 4226 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 090 090 000 - 10 188 Command_Timeout -O--CK 099 095 000 - 23 28 32 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 078 058 045 - 22 (Min/Max 22/22) 191 G-Sense_Error_Rate -O--CK 100 100 000 - 0 192 Power-Off_Retract_Count -O--CK 100 100 000 - 62 193 Load_Cycle_Count -O--CK 090 090 000 - 20982 194 Temperature_Celsius -O---K 022 042 000 - 22 (0 13 0 0 0) 197 Current_Pending_Sector -O--C- 001 001 000 - 19976 198 Offline_Uncorrectable ----C- 001 001 000 - 19976 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 5050h+03m+57.148s 241 Total_LBAs_Written ------ 100 253 000 - 2810919194 242 Total_LBAs_Read ------ 100 253 000 - 134650975240 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 5 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa1 GPL,SL VS 20 Device vendor specific log 0xa2 GPL VS 4496 Device vendor specific log 0xa8 GPL,SL VS 129 Device vendor specific log 0xa9 GPL,SL VS 1 Device vendor specific log 0xab GPL VS 1 Device vendor specific log 0xb0 GPL VS 5176 Device vendor specific log 0xbe-0xbf GPL VS 65535 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL,SL VS 10 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 10 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 10 [9] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e d9 67 08 e0 00 01:04:39.238 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:39.236 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:04:39.234 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:04:39.232 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:39.231 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 9 [8] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e d9 67 08 e0 00 01:04:35.569 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:35.564 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:04:35.562 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:04:35.560 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:35.560 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 8 [7] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e d9 67 08 e0 00 01:04:30.989 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:30.984 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:04:30.982 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:04:30.980 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:30.980 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 7 [6] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e d9 67 08 e0 00 01:04:27.270 READ DMA EXT 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:27.269 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 00 00 00 00 00 a0 00 01:04:27.267 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 01:04:27.265 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 01:04:27.264 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 6 [5] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 00 08 00 00 2e d9 67 08 e0 00 01:04:22.613 READ DMA EXT 25 00 00 00 08 00 00 2e d9 67 00 e0 00 01:04:22.611 READ DMA EXT 25 00 00 00 08 00 00 2e d9 66 f8 e0 00 01:04:22.448 READ DMA EXT 25 00 00 00 08 00 00 2e d9 66 78 e0 00 01:04:22.396 READ DMA EXT 25 00 00 00 08 00 00 2e d9 66 70 e0 00 01:04:22.393 READ DMA EXT Error 5 [4] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e d9 67 08 00 00 Error: UNC at LBA = 0x2ed96708 = 785999624 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 02 00 00 00 2e d9 1b 70 e0 00 01:04:17.549 READ DMA EXT 25 00 00 00 28 00 00 2e d9 1b 48 e0 00 01:04:17.543 READ DMA EXT 25 00 00 01 00 00 00 2e d6 ad e8 e0 00 01:04:16.026 READ DMA EXT 25 00 00 01 00 00 00 2e d6 ac e8 e0 00 01:04:15.927 READ DMA EXT 25 00 00 02 00 00 00 2e d6 9b e8 e0 00 01:04:15.686 READ DMA EXT Error 4 [3] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e e9 9b 28 00 00 Error: UNC at LBA = 0x2ee99b28 = 787061544 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2e e8 60 e8 e0 00 01:03:35.423 READ DMA EXT 25 00 00 01 00 00 00 2e e8 5f e8 e0 00 01:03:35.377 READ DMA EXT 25 00 00 01 00 00 00 2e e8 5e e8 e0 00 01:03:35.202 READ DMA EXT 25 00 00 01 00 00 00 2e e8 5d e8 e0 00 01:03:35.201 READ DMA EXT 25 00 00 01 00 00 00 2e e8 5c e8 e0 00 01:03:35.167 READ DMA EXT Error 3 [2] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2e e8 29 70 00 00 Error: UNC at LBA = 0x2ee82970 = 786966896 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2e e7 e2 e8 e0 00 01:03:29.367 READ DMA EXT 25 00 00 01 00 00 00 2e e7 e1 e8 e0 00 01:03:29.198 READ DMA EXT 25 00 00 01 00 00 00 2e e7 81 e8 e0 00 01:03:25.914 READ DMA EXT 25 00 00 01 00 00 00 2e e7 80 e8 e0 00 01:03:25.910 READ DMA EXT 25 00 00 01 00 00 00 2e e7 7f e8 e0 00 01:03:25.906 READ DMA EXT Error 2 [1] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2f 7a 40 40 00 00 Error: UNC at LBA = 0x2f7a4040 = 796540992 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2f 7a 3f c8 e0 00 01:02:55.434 READ DMA EXT 25 00 00 01 00 00 00 2f a1 a2 a8 e0 00 01:02:55.433 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 3e c8 e0 00 01:02:55.418 READ DMA EXT 25 00 00 01 00 00 00 2f a1 a1 a8 e0 00 01:02:55.417 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 3d c8 e0 00 01:02:55.416 READ DMA EXT Error 1 [0] occurred at disk power-on lifetime: 6344 hours (264 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 53 00 00 00 00 2f 7a 34 58 00 00 Error: UNC at LBA = 0x2f7a3458 = 796537944 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 25 00 00 01 00 00 00 2f 7a 2b c8 e0 00 01:02:48.536 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 2a c8 e0 00 01:02:48.530 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 29 c8 e0 00 01:02:48.524 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 28 c8 e0 00 01:02:48.520 READ DMA EXT 25 00 00 01 00 00 00 2f 7a 27 c8 e0 00 01:02:48.515 READ DMA EXT SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Aborted by host 10% 6443 - # 2 Short offline Aborted by host 10% 6370 - # 3 Short offline Aborted by host 80% 1648 - # 4 Short offline Completed without error 00% 1648 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 22/22 Celsius Lifetime Min/Max Temperature: 13/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Data Table command not supported SCT Error Recovery Control command not supported Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS
i
Modération : merci d'utiliser des images de petite taille (300x300) ou des miniatures pointant sur ces images (Des hébergeurs comme Toile Libre, TDCT'Pix le permettent).
Dernière modification par cqfd93 (Le 03/06/2018, à 14:51)
Hors ligne
#2 Le 03/06/2018, à 14:55
- inbox
Re : Erreur SMART
Salut,
Au vu de ces valeurs, ton disque est en train de lâcher :
197 Current_Pending_Sector -O--C- 001 001 000 - 19976
198 Offline_Uncorrectable ----C- 001 001 000 - 19976Il y a 19976 secteurs défectueux et non corrigeable. Cela signifie que les données situées dans ces secteurs sont dorénavant perdues.
Il faut donc changer de disque dur.
A+
Un problème résolu ? Indiquez le en modifiant le titre du sujet.
Hors ligne
#3 Le 03/06/2018, à 15:13
- theyellow29
Re : Erreur SMART
Ah merci 
Hors ligne
Pages : 1